Dorman 419-610 Accessory Drive Belt Tensioner Pulley

Worked great way cheaper than the local parts store!

Order two of the same smooth pulley for my 2003 Dodge ram 2500 5.7 l. Both the upper and the lower pulley are the exact same size and same part number. As you can see from the photo the new pulley is slightly narrower but the exact same diameter. Was a non-issue. the belt sits perfectly on the new pulley. Also note you'll have to remove the metal spacer that comes in the new pulley in order to install these. You can see the spacer in my hand and one of the photos. it just comes right out no problem. You cannot go wrong with dorman aftermarket parts. This is an excellent value and an excellent part. Highly recommend these as well as the dorman line of aftermarket parts!

This replaced the idler pulley on my 08 Ford Fusion 2.3L. This pulley comes with a gold colored cylinder that fits in the pulley which I decided not to use. This pulley can be used on many different vehicles so maybe in some cases the gold cylinder might make sense. I just reused exactly what was on my old pulley. If you don't it probably wont be aligned right. The old pulley had a big concave washer and a thick silver cylinder. Note how these are orientated when you take them off the old one. The concave washer wont fit as snug on the face of this new pulley but it doesn't affect anything. Also there would have been a little plastic piece to keep the silver cylinder from sliding off when you remove it. This was broken for me. It's not imperative to have it just makes sure the silver cylinder is fully seated in the pulley when you go to install it. Since I didn't have that when installing it I was worried it wouldn't get seated when I tightened it. As I got the screw tight I heard a snap and then the screw was looser again so then I kept tightening a little more and it got tight again. So this meant the cylinder slipped in to the right position and was seated. You could probably make a small little plastic piece from a bottle or something to put on there when you go to install. It does no harm and will just stay inside the cylinder. Also when you go to pull it out, pulling from the top worked from me although tight. Then I put it in that way too. Anyway my car is much quieter now! I used a mechanic stethoscope with a cone shaped end on it to pin point the noise. I recommend getting one they are not even $15. It can save you from changing unnecessary stuff.

This pulley is perfect for the belt tensioner and idler pulley on my 97 thunderbird. I had a bad squeaking noise and this fixed it right up. It fit great and went on easy. However the company over greases the bearings but it's not a big deal. The excess grease will come out. Just wipe the grease off of the pulley after about 50 miles of driving and it's good. I would absolutely buy again.

Got rid of the chirping pully

Worked perfectly

👍🏿

Equipment is fine. Is not a replacement for ford f150 2007 5.4l.

Le quedó a Mustang v6 3.8L 1999.

My belt start screaming and couldn't figure it out. Had the Alternator tested and this was the cheapest replacement, knowing the A/C was going to cost a fortune. You can hear a light squeal and see the osculation when I removed the old idler. Fixed my issue immediately, really easy to install. 1 13mm. Added a bit of lithium grease to the bearing. The original one in the 2002 Mustang GT had a steel ring with groves, whereas this one is all plastic and smooth. Didn't seem to make much of a difference.

Quedo excelente para Chevrolet Trailblazer 2002, solo tuve que usar la base de la polea original,..

This is a replacement Tensioner Pulley for the Tensioner Assembly on the Passenger side of a 2005 - 2012 5.4L V8 Ford F150, it also fits other makes and models and configurations but since Amazon lists these pulleys incorrectly I strongly encourage buyers to update fitment details to help fellow buyers! I own 3 different Ford F150 trucks, all with the 5.4L so this is based on my own uses for these Idler Pulleys, very easy to change and they are high quality as far a manufacturer specs, Dorman makes several components for OEM applications. Quality is 10 / 10, listing description is horrendous, luckily I read someone elses reviews to know I needed the 409-602 by Dorman to replace my Idler Pulleys on the Driver & Passenger sides of my oldest truck (2008). I ordered 4 of these to have 2 spares in my shop for the other trucks when needed.

Does what it is supposed to. Fits my 2010 F150 with 5.4V8