HandAll Beavertail Rubber Grip for Glock 17, 19X, 22, 45

Just what I expected with Hogue. I have a grip for my Beretta 92FS which is much easier to put on as it has removable factory grips, just swap em out. This grip has to be slid on, which made me hesitate, wasn't sure it'd meet my expectations. It's nowhere near as hard to slide it on as I was led to believe by the instructions it came with and AI! Heat it in boiling water, never gets too hot to touch being rubber, spray Windex inside the grip and with your hands stretch it over the bottom of the grip, pulling to stretch the opening bigger as you go. Once you get it fully started, it's easy to just twist and push it up the grip. Once fully on, twist to align the rear seam with the guns centerlines on the back of the grip. The Windex will dry out in a few hours and it will no longer twist easily. Fits perfectly on my Glock 21 Gen 5 and feels awesome as you'd expect from a Hogue grip!

So for the price this is an amazing item. I am 6'3" and have corresponding sized hands. My 9mm Glock 45 fits my hands well, but I still wanted a little more grip. This was the perfect solution. Grip feels much more solid and controlled. Installation is not easy at all. But if you work smarter you won't need to work harder. I used the boiling water and windex route. First, pour boiling water into a bowl and let the grip soak in it for 30+ seconds. While it is soaking spray the grip with Windex and don't be stingy, it should be dripping off. I installed it with the slide removed. Using tongs pull the grip out of the water, shake loose any residual moisture, and install as quickly as possible. I did not need to use the two plastic strips that they suggest, but it did take a few attempts to get the first part of the Hogue grip over the Glock grip. Once the first part is attached quickly slide it up using any means you can. The windex gets super slippery so I kept a towel nearby to dry off my hands during the process. I also re-dipped the Hogue into the hot water during the process. The trick is to be prepared and to move quickly but efficiently. Heat and windex are your friends in this. Be patient and deliberate and the install won't be easy, but will be possible.

I absolutely love this grip on my Glock 43X. I recommend heating it with a hair dryer to help with application.

Fits Glock 20V Gen 5, don't listen to everyone else!! The packaging doesn't list it, but if you look up Houge item #17020 you will find it listed as working for the Glock 20. It fits per the picture. Wasn't easy to get on, but I didn't need to boil it or use Windex, just muscle. Haven't tried it with the grip yet but hopefully it will take that tiny sting off the 625lb loads...

I’ll give it a solid 4 altogether! It is really hard to get it on, so I had to watch a few videos to figure out the easiest and best way to help it go because it was hard getting it to stretch around the handle- After attached the hand grip was perfect! It’s so natural feeling in your hand. It’s thick and easier to hold. It looks so good! The size is perfect!

Fits both my glock 17 and 19 , the best grip I've ever tried so far and I've tried multiple different ones in the past.

I have a Ruger RXM with the full size grip modual. The Hogue HandAll Beavertail Grip sleeve for the Glock 17 fits perfectly. This is the fifth Houge Grip Sleeve that I've bought. I heated it up with my wife's blow drier and it went on MUCH easier than I expected. I highly recommend it.

Best thing that ever happened to my beloved pistols. These grips increase control and comfort, resulting in better accuracy for me.

G17gen5へ装着予定でしたが、私のやり方が悪いのか全然入りません！

Excellent

Lors de la commande j'attendais vraiment un pistolet a air comprimé , et le résultat de la commande est seulement la poigné de l'arme ( pas très explicite) .

Love it! Fit perfect and feels very nice in the hand.

Nice grip