Mudder 5 Packs 9704230 Blender Replacement Parts Hand Blender Parts with 1 Wrench Compatible with Wp9704230vp Wp9704230

Nice, it got the job done. Thank you!

Pay attention to the wrench! There are no instructions and I did not realize that it was a wrench needed to unscrew the old one. I pried the old with a flathead and nearly ruined the alignment of a 28-year old KitchenAid. This was my second or third time needing to do it but I forgot the process. Just pay attention to the opposite spin than a normal thread direction. I have been using this for several months a couple of times a week with no deterioration.

Great repair set for my kitchenaid blender, great price and tools included

First - Why does the coupler break in the first place? - one way to break it is by assembling the jug incorrectly after washing it. The rubber gasket has to touch against the glass... if the gasket is placed against the plastic side instead, the drive shaft will be too high for the coupler (it reaches it only with its fingertips) and it will break. The rubber gasket "looks right" in either position, but only the glass side is correct and checking it will keep the coupler alive for a long time! (Ask me how I know...) It is literally a 2 minute job to install a new coupler. You will need a pair of pliers (the Channelock type is perfect for this). The easiest way to remove the old coupler is to just slide the little wrench under the coupler on the blender, then grab the coupler with the pliers and turn it CLOCKWISE (turning right) to unscrew it from the shaft. Note that this is the opposite direction of normal screws! To install - just screw the new coupler on ANTICLOCKWISE (turning left) while holding the shaft with the wrench. Hand tight is enough as this thread is self tightening during use. As far the the product is concerned, the material and workmanship look and feel good - the blender works as new again.

After destroying the original part on my blender, I found these. They're nothing but a cheap piece of plastic and a prime point of failure for the blender, but thankfully these replacement parts are easy to install, and because they're likely to wear out like the original, buying them in small multiples is a good idea and not expensive.

I saw my wife about to throw out our KA blender. She said it was not working and there were bits of plastic at the coupler. Our unit is well over a decade old. I checked and indeed the coupler had perished (rubberized plastic). Luckily I looked on Amazon and saw this part was a typical failure and somewhat easy to replace. I ordered this pack - which had five couplers and the removal tool for the same price as many of the two packs. I have photos of the failed part and the new part. Fits well and works as the original. Will update on longevity if needed, but so far save my unit from the recycle bin! (And these units are pretty expensive). Note: as others have mentioned removal and install of the coupler is opposite to normal as the treads are reversed which is typical in rotation devices (so they don’t get loose with use) - such as circular saws and angle grinders too. I used the supplied tool and channel locks to get the old one off. Review as of Dec 2024.

I’m so glad that I can actually change the part instead of changing the whole blender. The part appears to be as durable as the original, and it was a breeze to install. One thing to pay attention to is that the part is reversed threaded so tightening is actually loosening the part. 🙂

I recently bought this to replace the rubber coupler that melted while pureeing hot broccoli for broccoli and cheddar soup. Never blend anything hot in your blender. The rubber will just melt away, and I don’t understand why kitchenaid decided to make this part out of rubber. Stupid idea! The hardest part was removing the old coupler which took me almost a half hour to get the darn thing out. But thank goodness for the little tool. It helped with the removal. One thing you must know when removing the coupler is that you have to turn it clockwise. I kept turning it counterclockwise and it seemed to get tighter and wouldn’t come off, and then when I turned it clockwise it loosened up and I just kept turning and turning until it came off. Then when it came time to screw on the new coupler, I kept screwing it on and turning it to the right thinking it would just screw on easily. Somehow it just wouldn’t fit. I tried this many times and then I realized you have to screw if on counterclockwise( turning it to the left). And it went in so easily. This will save you a lot of time had I known this from the beginning. But anyway, it fit nicely. Let’s see how long this will last. If it doesn’t, I’ll have extras to do another replacement, but I hope I don’t have to do this for a long while. As for the seller, great service, good product, and it arrived in 2 days. Amazing, speedy service!

el producto llego a tiempo y en buenas condiciones recomendable

Fit perfecty. Excellent value pack

I have used 3 of these already, as other users in the household (and me) will shred the part every few years. a very cheap way to keep your kitchenaid blender forever and saving it form landfill. worth it. every time. lots of youtube videos dedicated ot epxlaining, with variang degrees of clarity, how to do the installation. they are rigth, the aluminium part of the screw just rips off the strong steel component its attached to, without damaging the base unit. have fun out therein kitchenaid land...

Fast delivery, only two days. Replacing the blender coupling part was so easy, thanks to the included wrench. Will order again.

Pour ma part ,une chance que Amazon est la !! Un mélangeur de 300$$ aurait fallut en acheter un autre. Mais ils en avaient chez Amazon, merci beaucoup