UTG Compensation Mount for RWS Airgun with T06 Trigger Black

Fit the rifle's factory rail and locked tightly. Just the right amount of droop compensation.

By JeffThe UTG compensation mounts is well made. I use it on my rifle, but I have to pay close attention to the position of the mount. The stoping do not adequately match with the provided holes in the mount on the RWS 34. I have to reposttion the mounts after a number of shots or the point of impact starts to change.

Works well and has not slipped on my Springer Air Rifles

These are very good droop rails. They stay in place very well. Machining is accurate. Less than a thou deviation.

This base is advertised as being made for RWS T06 rifles on the company website, though the recoil stop screws are reduced in diameter. The ends of these screws were cut-off for a proper fit. The angle worked perfectly to combat the barrel droop that is often inherent in these rifles. Overall it works great and looks great, though the stop screws supplied make no sense. Low rings can be used for most any objective size.

I put this on a Benjamin Titan NP that with a new scope was shooting about 6-7 inches low at 20 yards. It did exactly what I was hoping it would do. I was able to bring the scope back closer to the factory settings so I have plenty of elevation adjustment available. I have had scopes max out on elevation with a standard mount, this corrects that issue. I replaced one of the centerpoint/crosman pieces that had rails and rings all built into one unit. I did not like that in order to make adjustments to the retainer screw I had to remove the scope from the rings. This piece adds an additional point of failure in that now the rail can loosen from the dovetail and the scope rings can loosen on the weaver rail. Where as the one I replaced just had the dovetail attachment that could loosen. Since I loctite everything this should not be an issue though. The mount has performed perfectly so far. We will see how it holds up.

Works wonderfully on my RWS 34 (T06 trigger) and is of solid construction. This added 3/4 inches on top of the normal 1/8" built-in rail for a total clearance of 7/8 inches (barrel to top of Weaver rail). Use low profile rings for just about any scope. Ignoring any additional height due to the rings you pick (which there will be some), a 65 mm objective will fit.I currently am using the screw that's already present on top of the barrel as a stop-pin (just butted up against it). There are two pins in this mount that will go in the shallow stop-pin holes in the existing rail, which would move it forward from its current position. I will probably move to this position upon my next teardown, because the scope is a little closer than my natural eye position would want. My first attempt was to remove the large screw from the barrel and use the deep stop-pin holes, but that put my scope (13.5" long) much too far back (couldn't see).You should also be aware that with low rings, the flare into the ocular (eyepiece) will limit how far you can push the scope forward as it bumps up against this mount. The back of my scope is 10.5" from the butt, but would be about 11" with the shallow stop-pin holes. Use of a shorter scope may also help give you the spacing you need.Bottom line -- this greatly helps the barrel droop (vertical misalignment between the barrel and the normal 11 mm dovetail rail).

Works okay; well made. May still shim a little more, but works at near maximum scope elevation adjustment.

It works very well and holds the Scope securely on the Dovetail. Very well thought out and the quality is outstanding.

Sehr präzise gearbeitet, bombenfester Sitz dank 4 Schrauben & 2 Stopperpins; Vorneigung sehr praktisch! Passt optimal auf meine Diana und Weihrauch Gewehre.

works as intended, no instructions as to use of the numbered groves. raises the scope higher than necessary though. a lower height option would have been nice. also centers along the barrel unlike many others.

100% solid product when coupled with UTG AccuShot Premium 1-Inch Weaver Style See-Thru 10mm Low-Profile Rings. Item number RGWM-25L2. Does exactly what it advertises!

Supper good