[Upgraded 2026] ICBEAMER 37.8" 980mm Sunroof Wind Deflector,Universal Fit Tinted Moonroof Visor for Deflecting Noise, Rain and Windy Weather, Car Accessories Sun Shade Dark Smoke Smooth/Waterproof

The top of your vehicle is contoured so best to do these in the heat. follow the instructions after you get it centered and exactly where you want it. take a maker and mark where the back ends on each side go, make sure both ends are attached firmly where you want them. then do corners to center. press down and a bit back on bend. Look to makes sure your tape is touching. the straightness of the shield will bow up in middle so viewing the actual adhesive tape contact, continue pressing till it has no gaps.. I then sat my vehicle in direct sunlight to help the shield to adhere to the contour of my vehicle. an hour later i took for spin in 20mph winds and it held nicely..... if you clean the surface with windex, IT WILL STICK.

I was hesitant to buy this as it was adhesion only. All of my other cars used OEM deflectors using secure clip mounting. I prepped surface with rubbing alcohol to clean thoroughly. I warmed both tape and roof of car with a heat gun to promote better adhesion. Adhered to vehicle and left it inside a heated garage at 74 deg F. Did not drive car for 4 days. Took it out and hit the highway at 58 mph. It blew off the roof of the car, and hit the vehicle behind me. Luckily no collision occurred. The unit is advertised as using "3M waterproof tape". Wrong, It has a tape similar to 3M. It is a poor quality tape. See my attached photos. One is an extra roll of tape supplied with the unit. The other clearly a proper 3M tape. Note that the 3M tape used their logo on the backing liner. The unit supplied tape does not. Frankly, I find this disturbing. Using the 3M name when the tape is not. 3M "type" is what it should read. So to summarize. beware when purchasing this unit. Purchase some real 3M tape to replace the one on it. Also, the tape applied does NOT allow for any water to run off trapped under the deflector. It should have proper channels cut into the plastic to allow run off. OEM units do. On the plus side, it is a nice looking unit for the price. Too bad the quality is lacking in manufacturing.

Looked great but started coming off after only a few weeks, the double sided tape included isn't the strongest I put mine back on with gorilla tape been holding good since

Fit, style and quality of the visor was very good. I only gave 4 star rating because the double sided tape is lacking in quality. I done a good prep job and let the visor "cure" in 75* sun for a few hours. I did not drive it until the next day and it blew off 15 miles into my trip. Luckily I pick it up off the highway before another vehicle ran over it. I purchased good quality Gorilla double sided tape and done the same prep and same cure in the sun process and so for 3 weeks later its holding on rock solid.

This is a very affordable quality product. As with all accessories of this type it is made of durable acrylic with a dark smoke finish. It attaches easily using the standard double-sided auto adhesive tape found under the lip of the deflector. Simply peel off the tape covering and press into place. It's not brain surgery. When installing be sure to press down firmly along the lip edge and hold for a few seconds to ensure a firm grip. Make sure the surface is clean before installing and, like any other adhesive attachment, install when the weather is warm rather than cold to guarantee better adhesion. I have not encountered a single issue or defect with the product and am a happy customer. It's a pretty utilitarian product and if installed correctly I don't understand how people experience problems with it.

It's good sturdy acrylic but it did not fit right so had to cut some to custom fit it on my 2013 Ford Taurus limited the adhesive it comes with is crap make sure you buy some heat resistant 3m double sided tape cause the stuff they use is NOT 3M And does not bond no matter how much you prep it I bout the 36" one the smallest and it was still a bit too big!! If your willing to do all these it WILL work but if you just want to peel n stick it your going to lose it while driving guaranteed!!

It looks really nice, tight and secured on my suv. I’ve read several posts about the product not sticking, or flying off after applying. Well, After I cleaned the area with alcohol, I applied the extra tape to the tape that was already on the shield and bonded them with a heated blow dryer. After I applied the shield to my suv, I reheated the areas again with the hot blow dryer while applying pressure to enforce the bonding. After letting my suv sit overnight, Next day I’m driving 80 on the highway, still attached securely. I even tugged and pulled on it, it’s still securely attached. I’m very satisfied!

Was happy to find this @ under $50 and Amazon showed it should fit my 2009 Clubman S (R55). Purchased the 35.6”. On a 2009 R55, the sunroof raises above roof level and slides over the top of the panoramic roof, similar to a newer Ford Edge. First and foremost, this thing is curved and not flat on top. See pictures. When I originally fit the visor as shown in the ad and on the instructions, it actually PREVENTED my sunroof from opening due to the resistance. I had to move it forward on the roof in order for the sunroof to open. Were it 3/4” taller, I wouldn’t have had an issue with it. Due to the forward placement of the visor, it is now secured on the downslope of the roof. The adhesive—while strong—doesn’t have a flush attachment and the material of the visor doesn’t allow enough flexibility to make this a confident option. I will drive with it for the next week but am leery about entering a car wash with it. Will update this post in a week and may be looking for a taller visor. ***If your sunroof does not slide directly back and raises then slides as described above, you may want to reconsider this purchase***