SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting (Light Sensor, Delay Time, Sensor Distance, Adjustable)

I used this with my Kasa light strip, and it works really well. I've had it for a year now and it didn't fail on me

The media could not be loaded.  Got this sensor switch for some LED lights i installed in my safe. Does exactly what I needed it to. Open the door, lights come on! Close the door and the lights go off. I did have to open it up and adjust the three adjust setting screws to get it the way I wanted.All in all, was super easy to install, and once I read the directions to see which adjustment I needed, it works great! It has a motion sensitivity screw, that detects movement nearer or farther, and a 'lights on' duration adjustment.If you are looking for an easy solution to have automatic lighting, whether in a safe, cabinet doors, or anywhere a motion sensor could help you, then this may just be the one for you!! Highly recommend!!

This little switch works wonderfully! I use it as a motion detector in my home's entry-way to turn on 2 meters of LED strip when you walk in the door after dark. It is unobtrusive and always works correctly! I saw some reviews saying that there was no way to adjust it, but I had no trouble: you simply pop off the back of the case with a small flat-head screwdriver and the three blue dials are all immediately visible and accessible.The sensitivity dial controls how close you have to be to the sensor in order to activate it, and I set mine to about the halfway point, so it wouldn't trigger when someone walked down the hallway a few feet from the entry-way. The delay time dial controls how long the light stays on once it gets triggered, and it is super sensitive! Just a degree or two can change the amount of time by several seconds! The Light Sensor dial controls the lighting threshold. What I mean is that it sets a light level that the sensor bases its operation around: if the ambient light (the amount of light already present in the room) is below the threshold, then the sensor will allow itself to be triggered and turn the lights on when it senses motion. But if the ambient light is above the light threshold, you can't trigger the sensor and it won't turn on. This turned out to be an incredibly useful feature for me, because it allowed me to play around until I found a value that starts triggering the sensor around twilight/dusk.A quick tip for using the adjustment dials:When you are trying to figure out your values for the Sensitivity and Light Sensor dials, have the delay time set to its minimum value, otherwise you'll be wasting a TON of time waiting for the lights to turn off to try new settings. Also, when you pop the back off of the sensor to get at the dials, be aware that the sensor's circuit board is not actually screwed into place inside the housing, and so will fall out if you turn it upside down... Now, I didn't find this to be a problem for me, but it may disconcert some people, so just be aware.Because of how useful these little sensors seemed to be (as well as how cheap they were!!!), I bought 2 of them on my first order and boy am I glad I did. Now I have set them up at both my front and back doors, and I'm even thinking about setting one up for my internal garage door! I really can't praise this product enough! Just keep in mind that they were never meant to control an entire room full of LED lights; the maximum current on this thing is only 3 Amps, so don't overdo it!

This item solved a problem I had lighting a long, outdoor walkway on the side of my house. I needed an easy way to illuminate the path for people coming from either direction. The problem was that most motion lights could not monitor both sides of this walkway easily, or if they could, they would only control a spot light which was too harsh for my installation. I could have also used high-voltage motion sensors and wired them to an outlet, but then I would have had to install conduit. By using low voltage I was able to install them using small wires and zip ties without needing conduit.This replaced a couple of Insteon SmartHome motion sensors that broke over time. Since the company has since gone out of business I found that I had to DIY if I wanted to control the existing lights in a similar way. Using these, I was able to replicate the function of the Insteon motion sensors.I hooked two of these in parallel to a 12volt relay that was wired to an independent outlet in which I plugged incandescent rope lights. The lights were run the length of the walkway. Since there is one of these motion sensors on either side of this path, a person could approach from either direction and the rope lights will turn on (and anything else plugged into that 'controlled' outlet). I could have just used 12v LED lights and not needed the relay, but I already had the lights installed and wanted the flexibility to change them later on.

Works very good. Very sensitive. No delay. Works perfect for my LED shelf.

This motion worked out very nicely for me. I was looking for a way to light my gun safe. On YouTube I found a number of videos using LED lights to do this. One of them referenced this sensor as part of what they used along with the LED lights and power supply. I inserted the product link for them in this review so I hope they show up. It could not have been easier to do. Took me about a half hour. The results were excellent! There are three screws inside this unit to make adjustments. The information on the package is very brief and to me it was confusing. I started out by just setting them all in the middle and it was perfect! Several days after I received the item (and had installed it) I received with nice detailed instructions on the setting screws. I should have gotten it the day it shipped I suppose but it is helpful so if you are confused about anything just wait for the e-mail. If you're doing a gun safe check out YouTube. Otherwise a big thumbs up! inShareplus 12V LED Strip Power Supply 2A 24W, Wall Mounted 12V Switching Power Supply, 110V to 12 Power Supply for LED Strip Light with 5.5/2.1 DC Female Barrel Connector to Screw AdapterLE 16.4ft LED Flexible Light Strip, 300 Units SMD 2835 LEDs, 12V DC Non-waterproof, Light Strips, LED ribbon, DIY Christmas Holiday Home Kitchen Car Bar Indoor Party Decoration (Daylight White)

This has been fantastic. I walk into the room and my LED lights automatically turn on. Great upgrade for LED lights and well priced.

Pour tout ceux qui n’ajuste pas le capteur il est livré avec un délais de 2 secondes donc le remettre a un cycle plus long!! Tout fonctionne bien comme un charme reste a voir si il traverse le temps!!

bought in august of 21 and opened in april of 22.bench test both units and could not get to operate as they would not shut off. Tried several different adjustments and with no success on any of the settings. poor quality control on this product.

These are not tough or solid state motion sensors. They work well for what they are designed for ,which is indoor use. They are not waterproof and will run your average 12 volt LED, but if you try to run a 12 volt motor with one of these it may melt and burn up,under load.Just a bit too delicate.

Excellent product. It came really fast too. The only bad thing is that the adjustments can't be done without opening the case (Wich cannot be done easily)