BLACK HIGH TEMPERATURE HT SILICONE ADHESIVE SEALANT 70ml HEAT RESISTANT 300'C

Magic, Did what I wanted & more with my fingers, LOL Temp exceeded 300C Still looking good. Does not close & the silicon goes hard. It is very good in bonding & with stands heat very well. Very Happy. Pity it degrades after a year, I have applied it to my rear RHS car light unit, Zafira 2009B. Hoping this does the jo. will update later.

the inside glass panel in my oven fell out so i ordered this adhesive thought id try it and see if it would save me from having to buy a new oven .first of all it arrived in the post well before i was expecting it which was great tried it out following the instructions and its as easy as the instructions state was a bit tough squeezing it out of the tube but it worked a treat i will definately be buying this again and keeping it on stand by for any other repairs i need to make and the price compared to a new oven is amazing .

I needed to reattach my Bosch oven's roof liner. (The top & bottom of the liner are shown in the pics; a lot of area to be bonded!) . Couldn't screw it back as I'd inadvertently damaged the threading in the clamping screw's original hole. 🙄 I've many strong adhesives, but none that could resist oven temperatures. Googled & the only thing I found was the Technicqll. Though none of the other reviewers had used it to bond a roof liner, which is more load bearing than an oven door, I ordered it from Amazon & applied it to the areas of the liner that'd touch the oven roof, clamping it against the roof with some tight-fitting pieces of wood. Left it for 24hrs. (Needed to reapply it to one corner which I'd missed & leave for another 24hrs.) Some time after the cure time had passed I removed the wooden clamps & the liner was quite firmly bonded. 👍🏾 There was a sharp smell from the adhesive, but I'd expect this and so left the over door open after applying so it'd disperse. Obviously, as I've only just applied it, I need to actually *use* the oven & see what happens, but I'm quietly confident all will be copasetic. Based on its ease of use & minimal adhesion to surfaces you DON'T want stuck (i.e. the fingers), I'd highly recommend. (... If I don't report back after I've actually used the oven, one should assume that all *was* copasetic...!)

This silicone sealer is pretty much the same as others in general (ie a great product). However it has two great features. (1) It is suitable for high temperatures, and (2) it comes in a tube with a screw cap. This means it has a much better shelf life than the usual ones used with an applicator gun. So if you only need a little, and only occasionally, it is worth the extra cost. I only needed a small amount, and I needed it to be black. Therefore it was ideal for me.

My oven door became unglued. I tried it on my oven door. Yes it worked very well. Easy to use. Very good quality.

On first use, the tube with the nozzle allows you to distribute the sealant evenly. For any uses after that it becomes tedious to try and get any amount of sealant out of the tube. The nozzle can't be sealed once used so the sealant does what it does best, it seals. You then have to remove the nozzle and apply directly from the tube, but even this became difficult to do on the fourth or fifth use as the sealant cures. It's is a difficult product to work with and only worth using the first time in one go. The product does work but there needs to be a way to stop the sealant from curing in the tube.

Fearing I would have to go to the expense of having my electric oven door front replaced after one side of it became detached, I carefully removed the screws to find that it was just the rubber "seal" that had perished. I ordered a tube of this Black High Temperature Silicone Adhesive Sealant through Amazon which arrived within a couple of days. I must admit, I was a little sceptical, but after removing the old sealant and replacing it with the new, I was very pleased with the results! I use my oven on an almost daily basis and am pleased to report that I have had no further problems. I feel quite confident that if and when the seal on the other side of the door perishes in the same way, I'll be able to fix that side too! (Not bad for a woman who usually has to ask her husband to "fix" things - and whose husband was "well impressed" by my workmanship!) Brilliant results from a product that "does what it says on the tube" which, if I'd have called out an "expert" to fix, would have probably cost me an arm and a leg but cost me just a few pounds, and there's still loads left in the tube for any future "sealing" jobs that need to be done.

Works well, promtly delivered I used in for fixing windings on electric motors where the slighly flexible product with a temperature rating of over 200 C was useful.

Al horno de casa se le despegaron las 2 plaquetas metálicas cuadradas que van unidas al cristal mediante silicona. Tras mucho mirar me decidí por este producto, y la verdad es que no me ha decepcionado. Hay que tener en cuenta varios aspectos durante el proceso de pegado: -Que las partes a unir estén realmente alineadas en su totalidad al aplicar el producto (parece una perogrullada, pero si por ejemplo la plaqueta está un poco levantada respecto al cristal no se unirán bien ambas partes). Yo mismo cometí un error en este sentido y no se me quedó bien pegado, con lo cual tuve que reiniciar el proceso. Cuesta ver bien (por lo menos en mi horno) cuándo están en el mismo plano ambas partes, pero merece la pena escudriñar bien y asegurar este aspecto. -No aplicar una capa fina tal como indican las instrucciones (esto será válido para otro tipo de trabajo, pero no para el que nos ocupa). Yo me serví directamente del orificio del tubo y no utilicé el dosificador suministrado. De esa manera me fue posible aplicar una capa generosa en las dos partes a pegar. -Como es lógico, limpiar bien tanto plaqueta como cristal antes de pegar. Si se siguen estos consejos no debería haber problema en el pegado. Recordad que el producto aguanta hasta 300º. Si os soy sincero, no hemos utilizado todavía el horno, pero pensamos que aguantará bien la temperatura. De momento, pegado está bien pegado. Suerte.

impeccable 👍👍👍

Ho comprato questo Technicqll Adesivo sigillante siliconico resistente alle alte temperature 300°C nero perché mi serviva per sistemare una piccola perdita e sigillare una parte vicino a un punto che tende a scaldarsi. Non è un prodotto “da usare tutti i giorni”, ma più una di quelle cose che tieni in casa per le emergenze o le riparazioni. Prima impressione La confezione è piccola e semplice, il tubetto da 70 ml è comodo da tenere e non occupa spazio. Quando lo apri, la consistenza è quella tipica del silicone nero: denso e un po’ appiccicoso, niente di sorprendente. Uso nella vita quotidiana L’ho applicato su una guarnizione che non teneva più bene. L’applicazione non è complicata, ma bisogna avere mano ferma perché il materiale è abbastanza “colloso” e si attacca subito. Nei primi minuti è facile da modellare, poi inizia a fare presa e non puoi più lavorarlo troppo. Dopo l’asciugatura, la tenuta sembra buona e non ho notato più perdite nella zona trattata. Cosa funziona bene La cosa migliore è sicuramente la resistenza al calore: dà una certa sicurezza usarlo vicino a parti che si scaldano, e per ora non ha ceduto. Anche l’adesione su superfici diverse sembra solida, una volta indurito resta ben fermo. È utile proprio per piccoli lavori di riparazione domestica dove serve qualcosa di resistente e duraturo. Cosa convince meno Non è molto “facile” da usare se non si ha un minimo di pratica: tende a sporcare e non perdona errori. Inoltre il tempo di asciugatura non è immediato, quindi bisogna aspettare senza toccarlo. Il formato da 70 ml, poi, è comodo ma si consuma abbastanza in fretta se si fanno più interventi. Conclusione È un prodotto utile da tenere in casa per riparazioni mirate e zone ad alta temperatura. Non è un sigillante da usare alla leggera, ma se applicato con calma fa il suo lavoro in modo affidabile e duraturo.

I used this adhesive after deliding a CPU. I was able to easily cut/form the supplied nozzle to the right hole size. The glueing application went smoothly. I doubt that I will be able to use the tube and nozzle.

bra