KCT Nano-Texture Glass Screen Protector Compatible with Samsung Galaxy Tab S10 Ultra /S9 Ultra / S8 Ultra 14.6 Inch 2024/2023/2022, Auto-Alignment Tool, Tempered Glass

Very easy to apply using the alignment frame is a game changer. no bubbles, perfectly aligned once and done the first time. The matt non glare finish gives a great feel using the S-Pen and really cuts down on glare. No problem using the fingerprint reader at all.

Used on Samsung Tab S9 Ultra. Fingerprint sensor works great, no touch sensitivity loss. Mat finish looks great, doesn't hold Fingerprints or oils. Easy to clean if you do show some. Great protection.

The feel of this screen protector is amazing, very easy to install and has been holfing up great over the few months ive had it, i jist wish they made this for my phone too

Super easy to use kit but sadly bubbles..**Update. Most of the bubbles have disappeared on their own overnight. 2 remain.Upgrade from 3 to 4 stars.

I looked carefully at all others for my new Tab S10 Ultra. The protector checks all of the boxes for me, and is excellent with smoothness, and anti glare. The easy installation needs improvement, as there are issues. Read on for possible tips.I set up in my bathroom which is typically the most dust free room in one's home. I used a CLEAN very large nylon cutting board as a work surface. I had read instructions, and watched the videos. I had the ceiling exhaust fan running for 15 mins, and slowly opened the door when entering so as not to put surrounding air in motion. Kept fan on.1. I cleaned the tablet thoroughly. 1st with glass cleaner on paper towels, next with 90% rubbing alcohol on PLAIN DRY baby wipes. (I use these for cleaning optics on high end telescopes and astrophotography gear).2. I used a bright LED flashlight to look for dust particles against the turned off dark tablet screen. Any strays were brushed away with a dry cotton baby wipe. I also used one of the supplied dust stickers.3. When peeling off the 1st film, keep it facing the floor, so as to help keep dust free, and peel slowly. Make sure of your orientation, and place over tablet AFTER you have checked it for dust again.4. Touch the indicated area on left to start contact with glass, and WAIT until further suction has stopped!5. Pull the RED tab SLOWLY in a slightly side to side motion, not a straight pull. WAIT until all attraction to glass has stopped!!!!In my case, a small fragment of the rubberized ribbon remained under the glass at the instant it released (see photo). I used a small CLEAN stainless steel spatula to get under the glass, then twisted gently. The glass will lift fairly easily. I used the dust removal tape to snatch it, and let the glass settle again. I had bubbles at the 4 corners, and 2 about 1 1/2 inches from the right end, above and below the horizontal center. The corner bubbles were worked out quite easily. The 2 remaining wouldn't go away. I looked with the light and a magnifying glass. They appeared as bubbles, but with a defined center point. I grabbed the spatula, and lifted the glass again. It still lifted easily. I used the dust tape sticky side up and pressing the underside of the glass slightly toward the spatula. Removed both obstructions, let the glass settle, and worked out the corner bubbles. I was dust, fragment, and bubble free! Turned out these were glass fragments embedded into the adhesive on the underside of the glass. Tells me that the manufacturing needs improvement in cleanliness. The rubberized ribbon needs improvement, it shouldn't fragment. My alignment isn't perfect. Top and both ends are perfect. Bottom edge is approx 2 mm short from being flush. FWIW, The spatula I used is the type for artists mixing paint, in my case for removing objects from my 3D printer bed. I can also recommend having a can of compressed air, such as for cleaning computers, in case it is needed. Suction cups may work as well for lifting glass. I didn't think of them until after I was done. Above all, be prepared, and take your time. This is not a 5 minute job. I spent about 45 minutes, but now have a perfect screen.

The installation of the screen protector is a bit difficult. I cleaned the screen of my tablet (S9 Ultra) carefully, but I still had a tiny little dust speck after I applied the screen protector. I could gently lift the protector off the tablet on one corner and use the supplied sticky tape to get the dust particle out. Once done, the screen protector attached itself again to the table screen and a few small air bubbles were easy to scrape out. Now the screen protector sits flawless on the screen of the tablet.What I like most about this particular screen protector is the matte surface. It removes the glare of the regular tablet screen almost completely. Check the attached photos. One shows the S9 with the screen protector at the bottom and my old S7+ without any screen protector on top. The other image shows the notch for the cameras of the S9. The screen protector does not cover the front camera to prevent any distortion, i.e., in this notch you can see the original screen. Check how the reflection of the window frame almost disappears in the area covered by the screen protector.In addition, the S-pen glides very smoothly on this protector.