koolehaoda 50mm Arca Swiss Quick Release Plate & Clamp Set

I ordered this koolehaoda 50mm Quick Release Plate Clamp Adapter as I needed a simple way to mount my camera to a boom arm on one tripod, like the Arca assembly on my other tripod, and I wanted to be able to access my battery without having to remove the Arca plate. I have a Panasonic Lumix FZ300. It has a fundamental design flaw in that the battery door is too close to the tripod mount. Either screwed on to a traditional tripod or mounted via a quick-release Arca plate, as on my Benro Mefoto Roadtrip tripod, you can’t access the battery or SD card without taking the camera off at its tripod thread. . This Arca assembly seemed to be just what I needed, at a reasonable price. On first inspection, the overall quality significantly exceeds the low price. Everything about it is high quality, from the overall action and fit, to the rubber grip on the tightening knob. While my boom arm has a ¼”-20 thread, it is handy to have that 3/8” thread adapter for possible future accessories. . I first mounted the Arca adapter to my boom arm and confirmed that I can mount my camera safely to the boom arm in just seconds, versus having to precariously twist the whole camera around and around onto the fixed ¼” thread with the risk of dropping it. A scary operation at the best of times! The Arca plate is almost identical in form to that on the Benro tripod and works perfectly on that adapter also, as shown clamped in the attached photo. Unfortunately, the plate still covered the edge of the battery lid, just like the PU50 plate from my Benro tripod. However, lengthening the plain end of the slot allowed me to slide the plate over on the camera’s base by the needed 3 or 4 mm. As it turned out, the koolehaoda screw and its D-ring are slightly smaller than the Benro part and there’s just enough room to extend the slot and still use the D-ring. Not possible on the Benro plate. My battery compartment is now easy to open with the Arca plate installed and the plate will now be a permanent fixture on my camera for rapid mounting to both the Benro tripod and the boom arm tripod adapters. The four rubber pads on the Arca plate stop it from rotating on the camera’s single tripod screw under normal use, but of course, the plate can still slip if you inadvertently try and turn the camera when mounted on a locked tripod head. Did that, but just the once! :-( . At only $12 for the assembly, this koolehaoda 50mm Quick Release Plate Clamp Adapter is superb value. It works perfectly and upgrades any basic tripod for a rapid and solid camera mounting. . If you are looking to upgrade your tripod, or replace an existing Arca assembly, I can highly recommend this one. 😊

Well made and the spotting scope mounts securely and solidly to the tripod. The 1/4” adaptor that mounts the base to the tripod is more robust and did not shear and fail under normal torque when mounting.

These are great. I do frequent filming for youtube and am always switching between tripods and devices to mount on them. They are the perfect size, not too big to be bulky and add unnecessary weight but large enough to be sturdy and stable. They are designed very high quality and operate smoothly. You are getting very good product for very reasonable price. These allow me to quickly and efficiently move between cameras and other items without losing time during filming. I've bought several at this point and will continue to buy them as needed.

This mount fits my Peak Design plate perfectly and solved my problem of attaching my plate to the tripod without having to buy another tripod. It's heavier than I expected, but that's due to the good quality materials it's made of.

The 50mm Quick Release Arca Swiss clamp so far seems to be very good. It feels sturdy, and unlike some clamps, this one will open wide enough to insert a compatible bar from the top. Some others only open wide enough to slide the bar in from the side. Having both the hold down screw and the companion sleeve to make for a screw hole is nice, as it allows mounting the clamp to another item where it needs to be screwed down, or to mount a 1/4 screw item from the bottom (so it becomes usable on tripod heads that only provide a 1/4 screw on top). So far, I am pleased with the clamp. Time will tell how well it holds up to use. I've not had it long enough to comment on its longevity.

Quality build. Works great.

I was looking for an adapter for my older tripod that would mount on it and fit the mounting plate for my new Lemur Strap system. This product works perfectly! Anyone out there looking for something that will allow their Lemur system to mount on a tripod, this product will work as it has the ability to adjust to varying widths of mounting plates. It has a tightening screw that firmly keeps the camera in place once it's on the tripod. This product saved me the expense of buying a new tripod.

I wanted this to put on top of a leveling base head to make the base head quick-release, but the locking knob used to tighten the base impacted the head, rendering it useless for my application. So, my advice is to try to confirm that there will be no similar conflicts for your intended use, as otherwise this is a high quality device made of light yet durable materials and is engineered to fine tolerances. The quick release base is held firmly in place even when used with a long telephoto lens. If not for the conflict between the locking knob and the base of the leveling head, I would have kept it, but I returned it due to the conflict.

Ce matériel de qualité me permet de pouvoir adapter la plaque Koolehaoda sur la plaque rapide de mon trépied Vanguard et ainsi je peux mettre mon appareil réflex qui est équipé de la PEAK DESIGN Capture V3 qui me permet de porter mon appareil sur la sangle de mon sac à dos et cela m'évite de devoir changer de trépied, formidable ! Livraison très rapide

Tutto perfetto come da descrizione, ottimo rapporto qualità prezzo

This an excellent quick release plate. The tool free attachment of the camera plate is great. I have quick release plates costing more than twice as much from well known brands that do not have this feature. The locking screw mechanism is simple, quick and easy to use. No issues using this with my full frame Nikon Mirrorless camera and lens.

Diese Halterung nebst Schnellwechselplatte ist ein echter Problemlöser. Dank der Gewindebohrungen lässt sich diese Schnellwechsel-Klemme im Arca-Swiss-System problemlos auf Stative mit klassischer 1/4 Zoll Schraube montieren und damit lassen sich alte Stative im Arca-Swiss-System weiter benutzen, ohne dass man sich neue Stative kaufen muss, die dieses System nativ mitbringen. Diese Platte hat mir den Kauf von drei neuen Stativen und damit gut und gern 500 Euro gespart. Die Montage ist simpel, alles erforderliche mitgeliefert und die Klemme hält Foto- und Video-Equipment genauso sicher, wie spezielle und teils durchaus teure Arca-Swiss-Stative, auf denen dieses System fest montiert ist. Die Klemme ist präzise gearbeitet und hält auch Arca-Swiss-Platten anderer Hersteller zuverlässig. Ich bin da rundum zufrieden mit.

This is a small plate+clamp. It's what I was looking for. The clamp seems quite well made, no issues. I quite like the screw in locking for Arca clamps, having caught a sleeve on a more expensive lever type once.. This is on my travel setup, so small and light but sturdy is the metric used. Good quality. Basically identical to others on the market. The centre is nicely marked on the clamp.