Hood Deflector Protector Fit for Ford Bronco 2/4 Door 2021-2026

Solid hood protector that goes on in about 5 minutes. It's a nice, tight fit, and it matches the rest of the trim perfectly.

First off, I was very generous leaving a 5 Star rating as with most automotive items anymore these have an inferior adhesive tape either due to thickness or adhesion ability. I liked the design, and the fitment is excellent, but after reading the reviews of the wind deflector flying off of the hood after a short period of time, I was prepared to look into the issue that others have dealt with and find a way to correct the problem. It appears that the leading outside edge of the deflector has a small, raised border ridge. While it is not raised very high, it is raised higher than what the double stick mounting tape is thick, so in essence the tape does not make a firm contact with the hood of the vehicle. I removed the red protective plastic cover from the tape that is supplied and attached to the deflector then applied a second layer of STRONG double stick tape on top of their tape. With the double thickness of tape, it provides a strong solid connection to the vehicle. Follow the basics of cleaning the surface of your vehicle and then wipe it down with alcohol to remove any wax or other surface impurities. I placed the deflector on the hood of the Bronco and centered it on the hood then marked the center point with a soft lead pencil as a guide for mounting it once the tape is ready to be pulled once in place. Before mounting the deflector to the hood but after the cleaning stage I started the Bronco and allowed it to come up to temperature which also brought up the temperature of the hood surface, as the heat helped to bond the tape to the surface of the hood. I would occasionally later in the day walkout and press down on the edge of the deflector just adding a little additional pressure as the hood cooled and the tape set up solid. The design and fitment are spot on correct. I like the raised portion that runs from side to side adding an extra aerodynamic lift as the air flow is directed above the windshield. Hopefully it will also carry any small rocks, gravel or road trash right along up and over the glass wall that the Bronco calls a windshield.

Product is solid, made of of premium material. It fits my hood perfectly as well. Install took only a few minutes.

With less than 5k miles I've already had a windshield ding repaired, so I listened to the recs and bought this item. Thank goodness I put this on today before driving from Austin to Dallas! Less than an hour into my drive I saw (what seemed like in slow motion) a semi kick up a golf ball sized rock that would have destroyed my windshield, but instead it hit the deflector and slingshotted way over my new Bronco. The guard had a good sized ding in it, but not my hood or glass; so job well done! Would definitely recommend! Easy to install too.

If you don’t want stone chips on the leading edge of your hood this is the perfect solution. It’s made of thick black ABS plastic and matches the factory black ABS items (flares, top, mirrors, etc.) perfectly. I used to have a 1967 Bronco and because of the angle of that windshield (the 2022 Bronco’s windshield is a little more sloped) it seemed to be a magnet to stone chips. Back then the deflector was a straight vertical piece that helped save the windshield (and hood edge) from chips. This deflector has a raised portion along its back edge to help protect the windshield. I have my doubts if it will protect the windshield as well as the original style did, time will tell. This deflector is more aerodynamic which will help gas mileage (but no one buys a Bronco for gas mileage). The deflector mounts to the hood with double stick tape (seems every accessory mounts with double stick tape nowadays), it secures so good that after going through a car wash it maintains a reservoir of water until you drive away. The hardest part on installing this is removing the double stick tape backing on some of the small pieces.

The tape is already not holding the deflector in place. I washed the hood and used alcohol wipes to have a 100% clean surface prior to installing. Now I have to research and figure out how to remove it without damaging the paint. Why can't these be built like they used to be and attach under the hood instead of useless tape. Wouldn't recommend this product. Update August 2024....finally had to remove it completely. Adhesive is worthless on items like this...Definitely a DONOT purchase.

Has made a huge difference having this added. Not cleaning my windshield every day. I've had this for about 5 months now and have recently noticed that there’s slight discoloration and a slight indentation on a small section on the deflector over the past week. Not sure if something got underneath between the adhesive and the body of my Bronco to cause this. Overall works great

Fits great, looks great and easy to install

After checking reviews I decided on this to deflect the rocks and whatnot away from my windshield. It fits perfectly, looks good and goes on easy. I am very happy with it so far.

Quality product, good price.

Finish is patchy, with some parts shinier than others. Can be a challenge to get this lined up exactly right on your own, use someone else otherwise it won’t fit great, see my video. The included adhesive promoters where dried out, so useless. Now, the design flaw you’ll notice, is water will collect under neath and inside it, and when you wash your truck, all the water will collect at the lip. After a week or two, I can’t actually notice any difference bugs and stones still hit the windscreen, the only benefit is protecting the front bonnet from stone chips.

Bought this in July 2024 and installed it. 8 months on the Bronco and a 10 in section of it snapped off. DEFINITELY WOULD NOT RECOMMEND.