Rubber Seal Weather Strip for Tesla Model Y Juniper 2026 Accessories

Easy install but just be patient pushing the wiper edge thru the pieces mounted in the under side of the good. It's not difficult to do but does take some time. As for keeping water out from under the hood during rain or car washes it does a good job. Some water does get in there but I would say about 80% is deflected. Worth the purchase and the time it takes to install.

I was excited to have this sine the tesla has so much noise. After reading review, i gave it a try. Easy to install, but lack of instruction. For the girl to do car stuffs, i think more handy instructions would be great. Anyway, after 1st day you can see pieces falling off. And the noise not reduce that much, material is thin. I feel waste of my money and time.

This is a great idea. It was also the second one I bought. I installed the frame of the first one, then attempted to insert the rubber gasket through the frame. This proved beyond my capability! After nearly an hour of lying on my back, contorting in and out of the fronk, and struggling to get past the second joint I attempted to remove it to start again. In so doing I broke most of the wimpy plastic tabs in the center section. (Why they opted for a series of flimsy tabs rather than a continuous channel is beyond me!) So, I ordered a new one. This time I assembled the frame on my workbench; taped the sections together; then, with the generous application of dish soap, spent about 20 minutes working the gasket through the frame. Once that was accomplished, I installed it on the fronk and removed the tape. Naturally, one of the clips didn't really "snap" into place but it seems fairly secure, nonetheless. The instructions say it can be difficult but to be patient. My advice is to assemble the thing and then install it. (Not sure why Tesla doesn't do it in the first place, but....)

Works well to keep dirt out of the hood area. Don’t know about the decrease in road noise as I haven’t tested it but really don’t know if it made that much of a difference of a quieter ride. This was worth it to noticeably see the dirt difference in the hood

First I want to thank the others who posted about the poor adhesive quality. This is my install: 1. Replaced all adhesives with 3M thin double sided automotive tape cutouts, including to the two surfaces on the middle section with missing tape. To avoid frustration, prying 3M red protective film with the back edge of a #15 scalpel really helps. 2. Alcohol wiped area after removing old splash guards. 3. Inserted the right and left tabs only by their lateral clips, medial ends hanging in the air. 4. Inserted middle piece into the other two hanging by the tabs. 5. Pushed right end piece middle tab in but not completely, did same on left side, then pushed them in completely once center aligned. 6. Threaded the rubber edge pushing periodically in the right side to allow more to pull through, a 15-20 step process as rubber sticks. Wearing rubber gloves helps a lot also. The AC stench may be due to water constantly flowing onto the filters, as you can see this product does great shielding the air intake, photo was taken right after a car wash.

It made a great improvement in my Tesla. Outside noise is slightly reduced, but the biggest difference is heat retention—the cold air from outside is much less noticeable now. The only downside is that the two rear doors sometimes need a bit more force to close. Other than that, I’m very happy with it. I used 3M black super adhesive during installation, so I don’t think it will ever peel off. Overall, I’m very satisfied so far. I just wish the rear doors closed more easily; otherwise, I’m happy with the results.

Garbage. The adhesive is trash and does not stick. It worked for a few weeks and then all the piexes started to fall off. Terrible product and I'm past the warranty period

No instructions on how to put on the pillar seals. Sent a question to vendor and of course no answer. The only instructions is a video that is very vague. Half of the seals are coming off. Waste of money

Fait ce qu’il doit faire. Pratique pour retenir la neige en hiver. Faire l’assemblage avant de l’installer en place pour glisser la lèvre d’étanchéité facilement. Se clip facilement dans les ouvertures en place. Recommande le produit et le fournisseur.

Non buono. La guarnizione non si attacca facilmente e non sono chiare le istruzioni per la posa

Right fit

The rubber is damaged. The rubber band was received with a cut and torn at one end.

Easy to fit, Just assemble off the car including rubber remove the tape covers and click into place. Great product and should come on the vehicle. Tesla Model 3 Performance 2023