INJORA Silicone Rubber Insert for 118-122mm 4.75" OD 1.9" Tire, Green

Great product! Super easy to install and I won’t go back to dual stage foam any more. I installed this on my VS410 stock tire. Unleashed its full potential instantly. Just bought 2 more. Also it retains tire shape a lot better

These work really good in my trx4 sport. Will buy again for my axial cj7

Very soft inside Pro Line Toyo Open Country R/T tires. But exactly how I like mine, Truck has brass portal covers front/rear, Aluminum wheels, so it's not super heavy. The tires look like they're low on air

Fabulous. I inserted them in my Tamiya Lunchbox tires (RC Truck) and they do the job. They are easy to work with as well. I wonder if they could stand to be even a bit heavier and denser. They work as advertised. Durable. Fit exactly as described. Not overly sticky but just enough to make it easy to work with.

I got the super soft, and I gotta say, they are super soft. So beware, but I do like it that way, everyone at the rocks was saying that they are to soft, but I think the softer the better.

These things grip amazing! Threw them in my VS4-10 on some new rubber and it did noticeably better than with stock foams.

I've gotten these before for my 1.0 tires on my 1/18s and 1/24s, and this was my first set for my 1/10. The sidewall support is WAY better than stock foams, which is GREAT. I only knock a star off because of the extra work it takes to use these and properly vent THROUGH THE WHEELS, which is how I prefer to vent my wheels/tires. That innermost layer of flat silicone that hugs the wheel itself will completely stop air from passing through the vents on the wheel. What I have taken to doing is cutting off that innermost ring of silicone, so that what meets the wheel is just all the couple mm lines of silicone, instead of a big flat band of it. Not only does this allow proper wheel venting, it also improves the squish (deformation) of the inserts. (I've always been a little disappointed with the amount of deformation/compression with these. Those layers of silicone have nowhere else to go once the tire is at maximum deformation)

Fit great and perform well, these are very stout as described. Used them on the back tires only for my crawler.

Work perfect !

injoraのホイールとタイヤと共に使用しました。 デフォルトのスポンジインナーと比べると縦方向の潰れはイイ感じに変形するが横方向の変形は変にヨレたりせずに耐える感じで、なかなか良いと思う。 浸水してもスポンジよりは乾燥が早いと思うので、それもまた良いです。 1.55のタイヤも購入予定なので、その時もシリカゲルインサートを使用するつもりです。

Be careful with sizing these to your tyres. Somehow I managed to order the incorrect ones. These ones are too big for the 1.9" wheels they were going on. But as all my other tyre/wheel combos have Injura silicone inserts I think I can vouch for the quality of these.

Azules son más duras de lo esperado. Les corte 1 perfil si y 1 no en el aro más exterior, las suavizo y mejoró bastante la tracción. El detalle es q son diseñadas para los bastante estrechos neumáticos Injora. Para los neumáticos más anchos como los Canyon trail son bastante delgadas..tuve q cortar unos aros de 2mm de espuma tradicional , colocarlas del lado exterior y mejoraron mucho más. La dureza q ofrecen para las laterales es perfecto..no se deforman como las espumas tradicionales... con estas 2 mejoras q les hize mis Neumáticos Canyon Trail ahora van mejor aún.

Inserts efficaces