Victoria Manual Cast Iron Grain Mill 2400g with High Hopper

Great for cracking wheat for cereal or feed. This does NOT make flour and it doesn't say it does. I suspect it would also crack corn as well. But this quickly does a great job at what it is good for. Easy to set up and easy to use.

Let's be 100 per cent clear: this is NOT a dry grain grinder! Yes, you can use it to make peanut butter or grind coffee or even crack grains for cooking or brewing, but if you're looking for a flour mill my best advice is to buy an actual flour mill. This mill is intended to mill wet corn. It is very good at that. The very first thing to do out of the box is to wash the mill in hot soapy water. I like to put the mill body, front brace, auger/rotating burr and associated wing nuts spread out on a cookie sheet and put into a 250F oven for 20 minutes, then turn off the heat and let the oven cool. (I do not put the crank arm and wooden handle in the oven.) This helps insure that water is evaporated from the crannies where you can't reach with a towel. The very second thing to do is to get a couple of pounds of cheap generic pinto beans and grind them in the mill. The purpose of this is to remove any bits of the tin plating or machining swarf that may be left in the grinder. Throw out the ground beans because they will have metal bits in them. I grind masa three times through for best texture. I set the mill quite close for all three passes. I also made a "Masa Masher" wood pestle to push the masa down into the auger after the first pass. The website masienda.com has excellent videos about making masa; I encourage you to read and watch even if you think you know what you're doing. I took off the red plastic cover over the burrs. It's a good idea but masa tends to build up under the cover and squish out the back. This not only gets masa all over but it also partially blocks the burrs from clearing as you grind. I made an aluminum plate that fits just behind the stationary burr and is held on by the screws that hold down the brace. This allows masa to curl up but then fall into the pie plate I have under the burrs. Before each use, I recommend putting just a couple drops of vegetable oil onto the ball bearing inside the brace. That will help prevent wear in that spot, which gets a lot of pressure. I find an old toothbrush is handy for cleaning to get the masa out from where the stationary burr attaches to the front of the mill body. Leaving masa stuck in there risks mould, also rust. If you prepare the mill well, use carefully for the intended purpose and clean/dry well it should last for decades.

One of the comments complains about the "paint." It isn't paint but hot-dipped tin. It has been used for centuries, which is perfectly safe to ingest. The biggest problem with hot-dipped tin is that it inevitably has "pinholes," and in a subtropical island climate where I live, it rusts through the pinholes in only a couple of years. Probably no problem in a suburban or farm house in the north. I used primer and a number of coats of red engine enamel to prevent that. The machine works excellently and is solid; it will last forever.

The first use was to grind field corn cooked in calcium hydroxide to make masa harina for homemade corn tortillas. We use an electric grinding mill to make flour, and this mill will work to grind wet and also oily seeds. Easy to assemble and after use cleans up well. Yes, the corn tortillas were worth the effort.

Perfect for making my homemade multi grain bread with organic whole grains💜

Really wanted this item to work for me. Sadly, that is not the case . . . The item description clearly states: ✔️Capacity of adjustment. The clamp is easily adjustable to most tables and boards 1/2” to 2” thick. Comes with a protective non-slip rubber, protects your surfaces and prevents the grain grinder from slipping in heavy work If the description had clearly indicated the maximum opening of the clamp was 1.75", I never would have purchased it. It doesn't even come close to 2" as described. Well, I have a commercial wood block countertop made by Michigan Maple Block Co. that measures 96" long x48" wide x1.75" thick-- as you can see in the photo. The clamp mechanism barely opens to a couple of millimeters shy of 1.75" because the upper part of the clamp (which contacts the top surface of the cutting board) has a slight lip -- as you can see in the other photo -- and when the essential rubber protector is used to prevent damage to the countertop, it reduces the opening to significantly less than 1.75". Even if I could get the clamp over the countertop without the rubber base, it would definitely mar my countertop, which is why the rubber base cover was an important consideration compared to similar items. Additionally, the bottom of the hopper was slightly bent. I'm sure I could have easily restored its shape with a pair of pliers, so this is a minor QC issue. The clamp opening dimension is not a minor issue. Although this grinder is very highly rated, and I am sure works quite well for those with an appropriate suface on which to mount the grinder, apparenly few purchasers have a professional wood block countertop that is an industry-standard 1.75". I have no other surface in my kitchen -- all other countertops are imported granite with insufficient space underneath for a clamp -- or anywhere else in my home, so it's being returned.

I’m very happy with the purchase. The product was as described by the seller. The merchandise was carefully packaged and shipping was fast. I’ll recommend doing business with the seller.

!!!! DO NOT USE THIS FOR FOOD UNTIL YOU HAVE READ REVIEWS. THIS GRINDER WILL, WITHOUT QUESTION, LEAVE PAINT AND POSSIBLY METAL SHAVINGS IN YOUR FOOD. !!!! Other reviewers have written countless warnings and I took all into account before purchasing this product. I was fully prepared to take a cheap piece of garbage and work it into a usable machine, and that's exactly what will be happening. The WORST offense of this product is the coating. This is not a nitpick coming from almost every negative review, The ENTIRE machine is coated in metallic silver spray / powder coat, INCLUDING the grinding wheels. It is not a question of IF, you WILL get chips of paint in your food. It took me less than 3 rotations of the handle for the wheels to start spitting out shiny little bits of paint (see attached photos of the paint on my fingers and shorts). This is no doubt harmful to the consumer and is simply lazy on the producer's end. If you still plan to purchase this, please for the sake of yours and your family's health, give the whole thing a long bath in paint thinner, then give it some canola oil to protect the (incredibly cheap) cast iron from the inevitable oxidation. The LESS offensive problems would mostly come down to construction. Only the hopper is made of steel, the rest of this product is made of cheap powder cast iron that is improperly treated and extremely brittle, typical for cheap overseas metal products. There are extremely poor tolerances in almost every aspect, but they're manageable with small adjustments, new wingnuts, and rubber grommets. JB Weld is probably more structurally sound than the entire grinder so don't be afraid to glue it back together when it eventually snaps. The last complaint that myself and hundreds of others have had is the ridiculous amount of NON FOOD SAFE LUBRICANT that this thing was drenched in upon arriving. Smelled (and tasted, don't judge) like 3 in 1 machine lubricant. It was actually almost impossible to hold in my hand until three rounds of degreaser and dish soap. I'm still planning on putting charcoal through the grinder a couple more times to get the last of the paint and lube. For a $50 used, repackaged, powder cast iron that needed a little love and elbow grease, I would be perfectly happy to take this and shut up considering how much a good grain grinder is. But the fact that they are selling hundreds of these a month and implying that this thing is safe to use for food right out of the box is just immoral and frankly quite upsetting. I will be reporting this product and I hope you will too, it's literally criminal that this product is being sold without warnings.

Optimo

Para Uso doméstico puntual.

ممتاز واصلي القمع الكبير فيه طقات والبلاستيك فيه كسر جزئي لكن امازون كعادتها تعطيك حقك شكرا امازون

I am using this on almost the largest setting to split soybeans (which dehulls them) for making tempeh and soy milk. It works great. I can't see it ever breaking. So I'd say worth the price, since I'll own it forever. Although if you use it with wet ingredients you might have to be more careful about rust when washing it. I haven't washed mine since I use it only for dried soy beans.

鉄製であるためサビ対策が必要となることです