Electronic Component Kit Series for Arduino Motor, Raspberry Pi, AI Project, Robotics Set,STEAM KIT,Kids Adults Starters,electronic products DIY, etc. Arduino Motor and Tire/Wheels: Rate voltage: DC 3V6V Reduction ratio: 1:48 3V170mA; 120RPM, 0.7KGf.cm torque Size of the motor: 64.2x22.5x22.5mm(without the shaft) Diameter of the tire: 67mm/2.6 Width of the tire: 27mm/1.06 LM2596 Power Converter Features: Module property:Nonisolation buck Rectification mode:Nonsynchronous rectifier Input voltage:3V40V Input Current: 2A Output voltage:1.3V35V Output current:Rated current is 2A,maximum 3A(Additional heatsink is required) Conversion efficiency:92Percent( highest ) Switching frequency:65KHz Output ripple:30mV( maximum ) Load regulation:±0.5Percent Voltage regulation:± 2.5Percent Work temperature:Minus 40 degrees 85 degrees Dimension:43mmx21mmx14mm(LxWxG) Note: 1.Before powerup, please turn each potentiometer 20 turns counterclockwise 2.Input voltage must be 1.5 V higher than the output voltage. 3.Do not reverse the input and output interface. 4.Keep output under 2.5A and use a heat sink when for a long time working. HCSR501 Body Sensor Module Features: Operating voltage range: DC 4.520V Quiescent Current: <50uA Trigger: L can not be repeated trigger/H can be repeated trigger(Default repeated trigger) Delay time: 0.5200S(adjustable) the range is (0.xx second to tens of second) Block time: 2.5S(default)Can be made a range(0.xx to tens of seconds) HCSR501 Sensor Diameter:23mm(Default) Board Dimensions: 32mmx24mm Angle Sensor: <100 Degree cone angle Lens size L298N : B09522M8ZK Package: 2pcs xDC motors+ Tires/wheels 1pc xLM2596 buck converter 1PC xL298N motor Speed Controller 1pc xHCSR501 PIR motion sensor 3pcs x40pin male or female Multicolorful Dupont jumper wires Review: Well worth the money, Great value motor wheels for ardunio project - This is great robot kit, it inludes buck converter, PIR motion sensor, nmotor drive controller, these are all usually for DIY project , good work on my Raspberry Pi projected. dc motor and wheel will be used for another robot projecet. Review: Additional info would be helpful - The package contains everything included in the description. Unfortunately, it does not show instructions for putting it together or requirements. For example, most other Uno kits just require a breadboard and wires to connect sensors or motors. This kit requires you have a soldering iron and loose wire to connect to the motors. If the description showed this, it would have made a difference. Be aware of this info prior to purchase since the seller does not feel you need this information prior to purchase. If you are not already an expert, why would you purchase this sort of thing?
| ASIN | B0957J72VR |
| Brand | Maria Wang |
| Brand Name | Maria Wang |
| Customer Reviews | 4.0 out of 5 stars 3 Reviews |
| Manufacturer | Maria Wang |
| Material | Plastic |
| Material Type | Plastic |
| Model Name | gear |
| Speed | 120 rpm |
| UPC | 799086541551 |
| Voltage | 12 volts, 3 volts |
A**R
Well worth the money, Great value motor wheels for ardunio project
This is great robot kit, it inludes buck converter, PIR motion sensor, nmotor drive controller, these are all usually for DIY project , good work on my Raspberry Pi projected. dc motor and wheel will be used for another robot projecet.
A**.
Additional info would be helpful
The package contains everything included in the description. Unfortunately, it does not show instructions for putting it together or requirements. For example, most other Uno kits just require a breadboard and wires to connect sensors or motors. This kit requires you have a soldering iron and loose wire to connect to the motors. If the description showed this, it would have made a difference. Be aware of this info prior to purchase since the seller does not feel you need this information prior to purchase. If you are not already an expert, why would you purchase this sort of thing?
Trustpilot
2 months ago
1 month ago