Thermaltake Tower 600 Black Mid-Tower ATX Case; 3 Tempered Glass Panels; Hidden-Connector Motherboard Support; Rotational PCI-e Slots; CA-1Z1-00M1WN-00; 3 Year Warranty

I purchased this case after getting a 5090 and being concerned about its sheer weight of it hanging on the PCIe slot I knew there had to be a better way. Ultimately I stumbled across this case with its unique rotated motherboard design and knew it was perfect. Building: Space - I found there to be plenty of room to adequately manage my cable runs and still have remaining room for airflow. My 5090 fits with enough space to not pinch the 12vhpwr cable. Also there are smaller magnetic plates on the back that allow you to run the cables through their channels. Airflow - With the ability to have 3 120mm fans on the left and right side of the case both supporting a radiator should you want on top of space for 2 160mm fans on top and 2 160mm on the bottom, airflow is perfect. And I have to give a massive shout out to thermaltake for the fan trays making installation and maintenance simple. Along with thru included dust covers cleaning will be a breeze. Best of all in my opinion is the tool-less maintenance panels. They are either magnetic or held in with a push to lock system. Power supply… this is the one area I had the most difficulty with. There just isn’t enough space to accommodate the cables for the system. I feel like I had to stuff them in the bottom of the case. I have to highly recommend a modular supply as otherwise there will be too many cables in the way. My only other complaint is how the cables that will be plugged into the motherboard for peripherals like mouse and keyboard are pretty tight. Not a huge concern but if you tend to plug and unplug a lot of things from your computer the front io is going to be the best bet. This brings me to front io. With 4 usb 3.0 ports and 1 usbc port you really shouldn’t have difficulty with plugging things in. Lastly you have a headphone and microphone jack offering a wide array. Overall, I thoroughly enjoyed building in this case and find it to be ascetically pleasing on the desk. It checked my major concern of fitting a 5090 and in a way I don’t have to worry about GPU sag. I highly recommend the case especially considering its price and will likely buy another for my Girlfriends computer.

I love this case. Everything about it is a showpiece, so it's meant to be on full display on a desk or other sturdy surface. Don't hide this beauty under your desk or off in a corner! If you have a lot of RGB elements, they will really shine in this case. Pros: - Great visibility, you can see everything from the top mounted fans to the PSU cover on the bottom - Very sturdy glass panels that are press-to-release (like your grandma's old curio cabinet doors) - Compatibility with different sizes and configurations of case fans and radiators - Airflow! There's so much room for airflow and the sides are all protected by mesh covers - Sideways motherboard mounting gives a refreshing new look to an existing build - Hidden compartment on the back of the top panel for wires to run to the back of the motherboard, makes for a very clean looking build - Should fit almost any chonky or long GPU as long as you take one of the removeable metal coverings on the bottom off - Has the option to buy add-ons such as a screen for the bottom front panel and a stand to display the case on its side Cons: - Standoffs are low quality and the holes for them may not be machined right, I had to replace many standoffs with extras I had and even then, some had to be forced into the holes because they hadn't been machined properly - Back wiring can be an issue, especially if you have any kind of limited mobility in your hands. Lots of tight spaces, especially if you need to use the hard drive bay - If you don't buy the add-on screen for the bottom front panel, you may see wires through the mesh depending on how you wired your system - Very difficult to wire the PSU unless you have one with side-facing or angled connectors - You can't have Wi-Fi antennas installed on the back of the motherboard with this case, they will not fit. If you have an antenna that sits away from the motherboard it will be fine, but antennas that come directly off the back of the motherboard will not fit. I suggest using Ethernet for this case - Cannot put a radiator at the top of the case, only on the sides - Will need a splitter for the USB ports on the front of the case for most motherboard models unless it has two inputs for case USBs All in all, I'm really glad I bought this case even though the price made me feel a bit sick. I would not suggest it for beginners since the motherboard is rotated 90 degrees and can cause some issues with running wires, and the fans up top are a bit awkward. I can't attest to the fans that came with the case because I didn't use them, I already had case fans on hand that I used instead. Quality control on the hardware (screws, standoffs, etc) could be better but as long as you have extras on hand, it shouldn't be a big deal.

I had been meaning to build my own PC for a long while now, but never really had the urgency to do so, until my gaming laptop broke. I had been eyeing this case for a while, and when it came time to build, I decided to build around this case. I have very little regrets on choosing this case. It is aestetically pleasing, and taking it apart to build was a breeze. With the exception of the side fan brackets, you don’t need any tools to open the case to build. The case allows for back-connected motherboards, and cable routing is very easy in this case, it has holes in very convenient places and you are able to take off slots in the back to be able to access hard to reach places much easier. That having been said, there are a few flaws in the design of this case, but nothing that I would consider deal-breaking, or stuff that you can’t work around with a bit of creativity. *The one that everyone notes is that the Rear IO of the Motherboard and the input/output of the GPU is normally blocked by the top fan setup. While it is a pain to have to remove the top shield and the top fans every time you want to access the IO, this would only be a big issue if you need to access the IO constantly. I don’t need to do so, and removing the fans is as simple as loosening a thumbscrew and taking the setup off. I even went as far as using magnetic connecting fans at the top, so I don’t have to deal with disconnecting wires, or having them get in the way. *I decided to go with a back connecting motherboard. This case is set up to work with that sort of motherboard, and works for the most part, but I did find a couple of issues with that kind of motherboard **The placement of one of the USB3.0 header connectors on the motherboard made it an extremely tight fit for the extremely bulky front IO header, so much so that when I tried to route cables, the header began to snap. While I was able to fix the header, I was not able to plug it in conventionally. I was able to get around it by using the USB Header extension that came with the case, where the extension did not have the bulky design of the header itself. That allowed me to route the cables on the side as intended, allowing use of that header. **The placement of the 24-pin connnector on the motherboard caused the cables from the PSU to stick out to the point where it would not allow for 2 fans to be installed on the back as intended (this will not be an issue with a non-back connecting mobo). I was able to get a cable extension that had a 90-degree header to the motherboard, and that allowed me to be able to put the second fan on there. Overall, love the case, but keep in mind you may have to get creative in order to build in it.

It's an asthetic case for sure airflow is great if you have the right fans. cable management is versatile so that's nice every panel comes off so building was easy, the noise level is normal. And it's just small enough to bring anywhere.

The case looks very good but can be difficult to set up. Particularly the wires on the left side of the case routing through this very tiny space that looks like its rubbing on the fan but it doesnt just have to be VERY mindful of that gap I set mine up with a video of a YouTuber using this case but the case is definitely overpriced but if youre like me and stick with things for a long time price is fine i suppose Its very easy to clean with filters where the gaps are the panels just pop off Be very careful with the glass though. Its a push on top and it like releases 2 plastic arms that pinch plastic pieces and my top right piece to the glass broke off but the case come with a replacement or 2 i just havent replaced it bc im lazy I run an atx motherboard and a nitro+ 9070xt card from sapphire The top panel can be confusing so just follow the wires and youll be fine and my case runs extremely cool so far I wasnt able to connect all my wires to the case bc i have an msi pro series motherboard which is their budget x870e series so not enough ports but other mobos should have no issues I like the case and its the first pc ive ever built myself Im docking purely for price though i think the case on sale makes sense but i paid close to $300 usd after everything was said and done

Absolutely love this PC case! The Thermaltake Tower 600 looks even better in person and has a really unique design compared to a standard PC case. There’s plenty of room inside for components, and everything was easy to access while putting my build together. The vertical layout gives it a really clean look, and the glass panels make it perfect for showing off the build. It feels very well made and sturdy too. Definitely happy with this case and would recommend it to anyone wanting something that stands out!

Its been a while since my last Case upgrade. I was using an old school Coolermaster HAF case, however after picking up an Asus 9070XT card, my old case wouldn't fit the new card. I opted to upgrade to this case due to the unique tower design and aesthetics. Aside from the awesome looks this case has soo many handy features. The magnetic panels and slide out bottom filter make cleaning and maintenance super easy. My last case I had to basically disassemble the case and panels to access the filters. This is soo much easier. Cable management is also super easy, plenty of space and the channels with removable panels on the back make it easy to change out things without disassembling the whole build. I opted to orientate the GPU to the side view. You'll need the 130mm 90 degree riser that Thermaltake sells. Of note with this length you'll have to use the PCIE bracket slot that brings the card to the most front of the case. If you want to recess the card back from the panel you might need a shorter length riser as the 130mm pushes the card all the way to the front near the glass, you could probably bend it to push the card back however I didn't opt to. Also when orienting the card this way you won't be able to put a rad or fans on the left side as the GPU riser bracket gets in the way. I made the mistake of getting 3 additional fans for the left side opposite of my AIO. You probably could fit 2 fans underneath the Riser bracket but I chose not to put any for aesthetic reasons. Aside from the that this case is very much recommended.

Build is solid, it was a bit tricky in terms of cable management but all in all it looks amazing. Very happy with it.

Perfect, package arrived in perfect condition.

Adore this case. As someone who hadn’t built a PC before I was worried that it would be difficult to work with but all the detachable parts made it really easy to get to the more hard to reach areas. There’s plenty of room inside and made for a very simple assembly. One thing I will warn people interested in this case is that the case’s front 4 USB slots require your motherboard to have more than one usb 3 slots. Because of this I’m only able to use 2 of the 4 slots and the usb-c slot doesn’t work. The airflow and cooling on this case is great, it comes with fans in the top hidden away as well as multiple areas with dust filters for air to be released easily. Overall I’d say that this case was great value for money, easy for beginners and a cool look compared to the standard case.

It was an absolute JOY to build in this case, and I got to do it twice because I replaced my mobo shortly after transferring to this new tower. Pros: - Removable panels (absolute game changer and worth the price alone - never buying a case without this feature again), and the fact that they're all magnetic is perfect. No need to mess with screws. - Best cable management I've ever had - Easy to build in (see above) - it's the first time I didn't have to squeeze my fingers into tight spaces at odd angles to get things done - Absolutely stunning, just look at it! Cons (kinda): - Back panel (of the mobo) is at the top and covered by the top of the case and the top fan, both of which need to be removed to access it. (I don't have too much of a problem with since I don't fiddle with those cables super often and I like the extra dust protection, but you will find it irritating if you unplug-replug a lot of things) - Lack of drive bays (there are 3 tucked into the back (easily accessible) and it's absolutely gorgeous - I just wish it had more, I have a lot of drives and they're kind of just floating back there) Overall I find the cons very minor inconveniences. I don't regret this purchase for a single second! It's more money than I've ever spent (or even considered spending) on a tower, but considering the last tower I had lasted 10 years through several builds, I consider this an investment. Highly recommend!

It’s a bit tight in the back, and having to remove to top and fans to connect things to the motherboard is a bit of a pain, but it’s worth it. it looks amazing, it’s sturdy, and easy to remove parts and put them back together. Everything fits perfect, lots of room for fans and parts. It’s functional but also super fun. 10/10 recommend if you want a unique case that looks amazing!

Llegó un día antes y sin ningún daño, es tal como se muestra en la imagen. No hubo problema con aduanas. Excelente vendedor✨