ADIMLab Updated Gantry Pro 3D Printer with 310X310X410 Big Size 24V Power, New Type Direct Extruder, Lattice Glass, Resume Print and Run Out Detection, Modifiable to Upgrade to Auto Leveling&WIFI

I have have been playing around with this for just under a week, since it got delivered. I wanted to properly test it out before writing a review, and I can categorically say this is a very good printer.The printer comes semi-assembled and it took me about 45 minutes to get it printing (I was taking my time). It took me a couple of tries to find the optimal printing parameters, but after that it has been a dream to print with. I'm also very impressed with the general quality of the printer. All the cables are properly sheathed & labelled, the frame seems solid and the extruder module is very good (printing flexible filament is easy). IThe ADIMlab Facebook group is particularly active, and there is a lot of support/advice available.This printer is a great cheaper alternative to the Prusa I3 or the Creality CR-10 without sacrificing on quality. I'm thoroughly impressed.My only criticism would be on the location of the bed levelling screws, they are positioned pretty awkwardly, but I plan on adding the auto-levelling feature. Also, some parts of the technical documentation are badly written. None of this warrants a less than 5 star review.

Just received and assembled this printer. I have to say, it’s incredible quality for the money! I’m very happy with it so far, although I have only printed the basic test piece so far. As far as build quality though, top marks! I’m looking forward to seeing exactly what it is capable of =]

The printer is great - its a good clone, took me about an hour to do - but I am rubbish at DIY -so if I can do it - so can you. What I dont like: The levelling. Its advertised as an "auto-levelling method" - what it should mean - it should mean that the printer does bed levelling itself, what it means in reality with this printer model - it will move the nozzle to 4 places around the bed, where you must either use the paper levelling method or use some feeler gauges. I tend to go around the bed about 3 to 4 times as it tends to move slightly as you tighten or loosen the knobs for the levelling (it affects the level of the other areas) so go around 3 times to make sure its levelled ok. What I do recommend - PVA glue, a thin layer will make sure your print sticks to the glass plate. This must be done when its all cool, a VERY thin layer or glue takes about 15-20 minutes to dry up and almost disappear. Believe me, when you start printing - the first layer will stick like. er. glue. When its finished, wait until the bed is cold/room temperature - then the part comes off easily. Its weird but it works. Use rubbing alcohol to remove the glue. Aside from some niggles - this is my first 3d printer experience as aside from the bit of DIY of putting a few parts together (its 90% assembled for you already) tighten up the belt as its normally quite loose - the printer is good. I just wish it performed true auto-levelling as it can take 20 minutes at a time and touching the bed can throw it out. Also print bigger under-bed knobs as they're so small on the one they build, its a little difficult to get hands underneath. Its worth the money, if you're ok with a "little" diy, then you'll be fine and welcome to the world of 3d printing. Its brilliant !

i bought this 3D Printer for my son. had a few issues at the start such as faulty PSU but the seller got that sorted by replace the PSU. their customer service is great.it's very easy to assemble only takes about 10 minutes. levelling the bed and setting the height of the bed is easy. print quality is great.

I would recommend this product

Great printer once you work out a few details about it, and about 3d printing in general. I'm getting fantastic prints with both PLA and PETG, and with some PVA spread on the bed I have no adhesion issues at all. I'd definitely recommend the printer.

Brilliant printer for a beginner like me, had some issues with the extruder but the group on Facebook helped. Adimlab Joseph is the goto guy about them. 5 Star *****Needed some parts for my printer as I had a failure, I had the best experience of after care ever with Adimlab Joseph. Not only did he get the parts to me cheaply, he also offered some second hand ones as well for a very reasonable price!I now have 3 reliable and easy to use printers in my home!Many thanks to Joseph

Only just received but seems like a high quality, well built/sturdy printer. I also prefer the direct drive extruder on this, compared to similar brands bowden drives. Easy to assemble and get up and running, even if your not already experienced in 3D printing.