Wireless Caregiver Pager with Motion Sensor, Room, Bed Alarm and Drop Prevention for Home Elderly Children (1 Add-on Pager and 1 Motion Sensor)

Easy to setup and works very well

Overall at about $24 this is a good value and getting close to a great value if it drops closer to the low-$20s for a wireless motion sensor bed alarm / caregiver pager. Setup was straightforward – the receiver already had batteries in it and the sensor comes with its own as well, so it was basically mount the sensor, turn everything on, and pick a chime and volume. I like that the receiver can run either on batteries or from a Micro-USB power source, so you can plug it in by the bed or carry it with you around the house if needed. The motion sensor has a decent detection range and once I aimed it at the area where feet hit the floor it reliably went off when someone got up, and didn’t constantly false alarm as long as I kept it away from blowing curtains and heat vents. It’s also handy that the alarm sounds only on the receiver and not in the room with the person you’re monitoring, so you’re not startling them every time it goes off. There are multiple chime / alarm options and plenty of volume, so it can be a subtle doorbell-style tone or a louder alert depending on what you need. Build quality feels perfectly fine for the price and having both screw mounts and double-sided tape gives some flexibility on where to put the sensor. The only real downsides for me are that it doesn’t include a USB cable if you want to power the receiver that way and it’s really meant for indoor use only, plus it takes a little trial and error to get the sensor angle just right. But once dialed in it’s been a reliable way to know when someone is getting up or leaving a room, and for around $24 I think it’s a solid value compared to a lot of the more expensive bed alarm systems out there.

I write very, very few reviews; but I'm making an exception with this product. It actually works and works great. I highly recommend these simple alarms. I have four of them, all of which are the plug-in kind with batteries for the motion detector. My wife of 56+ years has late-stage Alzheimer's disease. The first one I bought wakes me when my wife gets out of bed. Part of the reasoning for that is she broke her hip a couple years ago and had to have a total hip replacement. I don’t want her to fall again. The receiver (the plug-in part) is connected to a power strip which is fastened to the bed post with a couple of zip ties just above my head. That close to your head, it will just about wake the dead, which I need when I’m asleep. The power strip has a switch with a red light that I can easily turn off to silence the alarm. The red light lets me know it’s on with a glance, even in the dark. The battery operated motion detector (transmitter) is simply sitting on the carpet on her side, underneath the bed. I’ve had it a little over a year and only had to change the batteries one time, just recently. When they need replacing, the alarm sounds and stays on without motion, suggesting something is wrong. When I replaced the batteries it worked again, just like new. Since I bought the first alarm, I’ve purchased them three more times to give me peace of mind when my wife moves about the house. One is sitting on the floor beside the front door to let me know she’s there. They help me keep track of where she is, but by themselves, they're not fail safe. I’ll explain later below… The picture with three receivers plugged into an outlet is in the hall just outside our bedroom door. The left receiver is for the indoor motion detector that sits on the floor just inside the front door. The one on the right is for the motion detector (transmitter) on the back porch. The middle receiver is for the exterior motion detector on the front porch just above the door. Each alarm each has up to 50 different alarm sounds that can be customized to help you distinguish which alarm is sounding. Some tunes are kind of 'cheesy,' but most of them are quite good. I chose a police siren for that one to distinguish it from the other two alarms which have similar, but not the same tunes. I can hear them from most areas in the house. The other two motion detectors are actually mounted to exterior walls: One, above the front door under a covered porch. The other is mounted on the exterior wall above the sliding glass doors on the back porch. Both of them are protected from rain by the porches. if you decide to buy one, you’ll notice that the included directions are not written very clearly. And, they’re written in tiny mice type. I wrote and rewrote them through much trial and error which I included below. I said earlier that these are not fail-safe devices. Because of that and the fact that my wife “escaped” several times before I had our home somewhat “dementia proofed”. I did this by adding another security device inside, near the top of the front door. I finally have some peace and a sense of security. There is also a picture of it on the inside of the front door. It's also from Amazon (see link below), costs less than $15 including tax. It's easily installed; it works great, and my wife cannot understand how to open it. It's simple to open for normal people and would also make a good security device for people in apartments, etc. It can be installed on either a right-hand or a left-hand exterior door that swings inward like ours does in the picture. I think it’s a must have for a loved one with dementia that’s prone to wander or has “sundowners” symptoms that are prevalent with Alzheimer’s. I very highly recommend this product as a potential life saving device. Link for door security device --- https://www.amazon.com/dp/B07DR9CMGZ?ref=ppx_yo2ov_dt_b_product_details&th=1 Pairing the Receiver & Transmitter Plug the receiver into an electrical outlet and set the transmitter on the floor near the outlet pointed away from you so you can easily activate it in step 4 below… 1. Make sure the Motion Detector Transmitter is ON and pointed away from you. (the smaller battery-operated unit) 2. Set the Receiver ringtone by plugging it into an outlet and short pressing the lower button until you find the tune you prefer. Deciding which tune to use is the only hard part... 3. To activate Pairing Mode, Press and HOLD the Receiver Volume (upper button) for 5 seconds until it sounds and the LED's begin flashing. 4. Complete Pairing by waving your hand in front of the motion detector within 5 seconds. 5. When Pairing is successful the unit will activate the new Receiver ringtone whenever motion is detected by the Transmitter. (There is a 5 second delay between activations; but this can be changed to immediate within the Transmitter)

You can mount this to the wall, door, ceiling, and it works great. There are many choices of sounds to alert you, but the default dingdong works well. You can adjust the sensor up a bit so wandering pets don't trigger it. I keep the receiver plugged into a powerbar with a off/on switch so it can be moved and plugged in just about anywhere, and turned off when not needed or wanted. Very happy with this unit.

This helped me to take care of my dementia husband when he first came home after a long bout in the ICU and physical therapy home. Loud and adjustable. Small and easy to strategically place it where I wanted. Motion detection is great. During the night, you might want to place this under a pillow, to mute the sound a bit. You will still be able to hear it, but not so loud to alarm you or your loved one.