ARCTIC ケース冷却ハブ 10分岐 PWM分配 SATA電源対応 PCクーリングコントローラー ブラック

Easy to install and works well... I wish there was an instruction manual.

Works fine I just dont give it 5 stars because of how difficult it feels to disconnect the fan cords. I felt like I had to pull it tot hard and I didnt have a room for holding other than the cable itself so I think it could easily be damaged. Other than that, the product works well and it's very easy to set up.

冷却ファンの増設用に購入。 ファン6機接続しました。 PSU1000WにSATA接続したので電源の問題なし。 発熱も問題なく、PWM制御も問題なしです。 暫くは様子見ですね。

PWM分配を謳っているが、商品写真６枚目を見てわかる通り２ピンで本体とマザーボードを繋ぎます。つまりファンの調整はできず固定で回ります。UEFIで確認してもN/A表示でした。

マグネットは内臓されていないため、減点１です。それ以外特に問題がありません。

とあるPCケースが最初から6基のファンを搭載しており古いPCケースからの流用でもう1基ファンを搭載するために購入。この製品自体は4-pinに対応しています。つないでいるのは全部3-pinのPMWではないファンですが、後々PMWファンを使う時があっても使いまわせるのは心強いです。 マザーボードのケースファンコネクタが1つしかないのに10基までのファンを付けたい時に役立ちます。 ARGB等の光らせるファンには対応してないので光らせたい人はARGBにも対応した別の製品をおすすめします。 両面テープのついたマグネット板同梱でPCケースの金属部分に張り付けられるので、ファンケーブルのテンションに気を付ければある程度固定できます。 本体自体は大きくも小さくもなく、重さも軽いのでそうそう自重で落下するものではありません。 電源供給はSATAで供給するタイプ。電源やSSD/HDD事情にもよりますが、もしSATAの数が足りない時はペリフェラルをSATAに変換して使う必要があるかもしれません。 ファンハブを使うのは初めてだったので、他所の品と比べることができませんが1200円前後の値段で概ね予想どうりの製品で満足しています。

ممتاز نفس الوصف

Cheap, easy to install, and works perfectly. Initially I had issues with the PMW control however this was my own fault as although I thought I plugged a fan into port one, I hadn't. Move a fan to port one and it worked perfectly. Feels a bit flimsy but it's not like I'm going to be handling it on a daily basis. It's a plug in and forget situation.

Cumple con su funcion

Bu kadar işe yarayacağını düşünmemiştim. Ama çok memnun oldum.

You can replace this thing with models from most any vendor. My use case makes the enclosure desirable, and this model wasn't much of any more expensive, even compared to many of the dubious Chinese vendors selling fully exposed PCB. For mounting you're given two options, double-sided adhesive, OR magnetic. The magnets are not especially strong, but don't need to be particularly powerful. Either way you can conceivably mount this in any case of any variety, somehow. I even have one of mine slapped onto the side of the PSU. Not much else to say. Simple device, and while there is a lot of competition on the market, these remain competitive in price. You could stand to save a few bucks on other products with exposed PCB, but unless you are buying exclusive to your exact model of case with precise mounting standoffs I would be dubious of so many exposed contacts. Price is always the arbiter, but I am not sure how much more expensive something like this would need to be compared to cheaper raw exposed PCB products. In my case the difference was about 2 dollars. I figure most fan hubs lacking housings are at least shielded on the rear, but I needed both sides enclosed. There was no way I could make up the difference without spending more - and certainly wouldn't care enough to figure out how true it is at a difference of ~2$. Even comparing 6$ difference to brands I wouldn't trust in a server if you paid me it is a trivial distinction. If you're buying bulk, get special order exclusive to your screw mount options.