Mr-Label-Wrap Around Cable Labels

The labels stick well to cables, and also stick to themselves well. Printing with a laser printer works well, but the template for libre office took a bit of revision. After a few rounds of trial and error, printing with libre office and a laser printer did work. Writing by hand with a permanent marker also worked well, and is faster for making just one or two labels at a time. The downside to good adhesion is that removing these labels can be difficult. I don't know about durability, I've only been using them for a few weeks.

haven't tried printing on these yet. sharpie, precise sharpie, and ballpoint pen all work fine. very sticky tape and seems like it will be durable but i won't know until months/years from now. i'm using these on cables for music gear, some of which will see alot of abuse. just take your time when you're applying them to cables and they'll go on without wrinkling (or wrinkling too much). So far for the larger cables, no problem. But for very very small cable (think 1/4 headphones), already a tiny edge of the tape has come up. It's no undoing itself but i can see that this will catch on the cables. I think for permanent installations like network closet this is no problem at all; but if you're using this for music gear for live shows, it's something to watch out for.

I like them with some help. If you put these on cables directly they are very hard read. I put some 1" white duct tape under them and a huge difference in legiblity. The template for printing wasn't the best but with a little bit of time you can make it work. I would definitely follow the directions and print on regular paper first before printing on the labels themselves. I will continue to use them as I like that there are multiple colors so I can denote length with the color and help keep my cables from walking away with the text. They seem pretty durable but haven't had them long enough to know for sure.

I'm impressed. Labels are running through a xerox printer, using manual feed of printer. Have only feed one sheet at a time. Took some test runs aligning rows and columns using excel. Labels did not peel when going through printer. I would not try running sheet twice. Label width is decent. It would be nice if they made a double wide label also. Recommended.

I would not recommend using these inside a laser printer (even though it says they can be). When I ran it through my laser printer, a few of the labels detached from the backing and stuck to the drum/belt and melted to the fuser. I was able to carefully remove the melted material from the fuser but the drum/belt has sticky residue on it now and it leaves artifacts on all my normal print jobs now. I have to buy a new belt unit. I have had success using them with a fine-tip permanent marker. They work great using that method.

I'll never buy another label from anyone else. I've got stacks of labels sitting around that where just impossible to use unless you like to try and read bad handwriting. Mr. Label has templates for their labels. Easier than you can believe to label cords, items, anything when the template allows you type and pring!!!

I liked the entire concept, especially being able to print out legible labels for power cords, USB cables, Ethernet cables, etc. However, after a few days to a week, the edge of the laminating part started to peel up slightly. This was easily and quickly remedied by placing a small piece of cellophane tape over the label. However, if I have to place cellophane tape over my labels I could have just used regular labels to start with and put tape on them. Thus, these are less of a time saver than I had expected, but the color coding is nice. PRO TIP: Black printing on the red labels is pretty much unreadable without a flash light.

Even though there are several reviews about the labels coming off during printing or delaminating I wanted to give them a try due to cost. Before printing I checked to see that they were well attached to the backing sheet and they seemed to be securely attached so I printed 8 labels as a test. The Open Office template you can download from their website worked perfectly. They came through my Lexmark laser printer with no issues. I then affixed them to each end of 4 new patch cords and waited for a few days. They are still attached solidly. I think there may have been some lots that had poor quality control with the adhesive, but mine appear to be good. They compare to the Panduit labels I have used previously at a fraction of the cost or the need to buy in a large volume. Note: some text in picture redacted. Its not a printing smudge.

Feuilles très pratiques mais format de feuilles en 21,7 x 28. Pas de modèle fourni. Délai de livraison énorme (presque 1 mois !!!)

Good concept, but they do start unravelling after about a year, although they have stayed stuck to their respective cables, nonetheless.

Buen producto el pegamento podría mejorar

Template is rubbish, make sure you peel off the redundant part of the sheet(the skin around the actual labels) before you print

Si lo que buscas es etiquetar tus cables, no las recomiendo en lo absoluto, el proceso de impresión es un caos, tienes que realizar un montos de pruebas con Word, Excel o con programas para etiquetado, su pegamento no es permanente así que los pones y al ratito ya están despegándose, no las recomiendo porque el etiquetar cables debe ser perfecto, rápido y seguro.