Qasim 1-Pair 80MM White+Amber Switchback 102SMD 4014 LED Halo Ring Angel Eyes Led Lights 12V

Nice LED rings, there's no adhesive like the older ones had. The in line module is a little big, and the small plug that connects it to the light doesn't have a lot of tension in it, I had to play with one of the connectors to get one of the 4 I purchased to work.

Great looking and really bright, perfect fit on 2002 pontiac firebird, super upgrade,...i silicone them on the back,make sure they don't get wet. I used 1/4" 3m tape to stick them on top of the existing lights. Bought 80mm and 110mm version on my car. Thanks so much!

It’s definitely not Morimoto Quality, but it’s great for a Chinese knock off at the price. I’m only giving 4 stars because how thick the covers are over the diode board. It’s massively thick to me compared to previous builds I’ve done.The switchback function works flawlessly on test bench and are super bright. Also, the pins on the connectors are easily removed and re-installed being a bonus as most of the time you have to have a tool. I would definitely recommend these for a first time build or a daily driver type build. I’ll post pictures of finished product when I’m done. I’m still waiting on projectors.

Very bright, flawless plasma look. Clean, easy to hook up, gorgeous look. I originally had some pretty bright led lights for my blinker signals but wasn't happy with just the bulb so I went with these halo rings. I didn't have much money to spend at the time and so I went with these because... you can't beat twenty bucks! I was skeptical because of the price but when I received them they came with plenty of wire, optional amber or white lighting and were incredibly bright. They put my LED bulbs to shame. These are definitely worth the money. They work like a charm and look beautiful.

This is a nice looking LED switchback Halo. Its bright in both the white and Amber colors. Waterproof... Eh... Not so much. I have ordered a couple sets of these now because they are so cheap. But they definitely not waterproof. First set I didn't do anything to the lights just put them on my fog lights. By the time winter was over half the LEDs had shorted out. By the end of the summer the controller shorted out and almost took out my whole light assembly.(my fault as I should have replaced them way before that). I put on a new set but I went crazy with the silicone and put some around the edge on the inside and covered the back LED board. Well I didn't do a good enough job on one of the halos because it only took one rain storm and it already has LEDs that have shorted out. And with every new rain/snow storm I lose a few more. Other side still looks brand new so I must have done a much better job there. Just ordered my third set to try again. I plan to be a bit more meticulous this time with the silicone.

Work as they should. Installed on a four wheeler looks good

Value for your money

Retrofitted my own headlights and put these Qasim halos behind the shrouds. One light stopped working no more than a week after installation. If you look at the picture attached, they used two black cables from the halo to the driver. That's not typical, the output has one black, one orange and one yellow. That's what should be going in also.Anyway... I'm disappointed. I'm going to have to go through the pain of changing this light out by opening back up and tearing down my headlight. Sucks.By the way, Qasim will not replace the halo because it is out of warranty - I took too long to install this after the purchase.

Works great on the Vmax tied in the existing led blinkers. Combined them with a set of 70mm. Ran an LED driver for each LED (2/side) and they work great. Super bright!! You cannot say you did not see them!!Sealed them all up with clear silicone to make them water tight. Great customer service emailed them a few questions and they got right back to me.

Installer sur une moto Lumiere très lumineuse et sécuritaire sur la route et le service après vente très bien réponse rapide

nice and bright for around the quill of my mini milling machine. my only wish was that the wires were more robust

I made the white as DRL and the amber connected to turn signal. I am happy with this lights.

Tel que décrit