TOURBONNeoprene Adjustable Cheek Rest Pad Comb Raising Kit Recoil Absorbing Buttstock Sleeve - Black

Hard to install but good fit once installed

was tough getting it on my shot gun but once I did it seemed to do what it is supposed to do

This kit is a must have for the long range hunter or marksman. It provides a cushioned check rest to help reduce the effects of recoil while maintaining the correct eye alignment with your optical scope. To me it makes all the difference to maintain proper solid contact with the gunstock without pain causing a possible flinch.

I purchased two of these for two rifles so that my cheek weld would be made by looking down the center of the scope. After trying various methods of slipping the rubberized sleeve over the stock, I found that it was easiest to select the appropriate-sized riser, set it on the top of the stock, and then turn it over onto the stock and riser. To do this, it is best to slip the sleeve onto the stock and bunch it up toward the stock's pistol grip. This device would be particularly good for adjusting the stock height for trap-shooters. This is especially appropriate for younger shooters so that they can learn to keep their cheek on the stock in the right place so that they don't have to crane their necks to get the proper sight picture without raising their cheek off the stock. I've seen instructors tape towels to the stocks, and use various other methods to raise the stock to the proper height for a learning shooter. This is clearly a better alternative, especially since there are three separate-sized risers that come with the rubberized sleeve.

This was a bit difficult to get on but I finally managed to do it. Put the sleeve on the stock first, then roll it back on itself, next put the piece of foam over the stock, and then pull the rolled sleeve portion back over so that it completely covers the the rise and comes down on the other side toward the end of the stock.This is not a bad product by any means. It is just that it is not capable of being fully stable.I got this to work but I'm not terribly happy with how it shifts around on me. It's on there about as tight as anyone could hope to make it. This is pretty good for an interim solution but I'm going to have to find another another product to use permanently.Putting being able to brace your jaw up against the stock greatly improves accuracy and precision. You're able to then put your cheek or jaw up against this and get just the correct I relief to be highly consistent in your marksmanship.If anyone has a suggestion for me I would very much like to hear about it.

It's very very hard to put on. But I think it needs to be tight. It works, nice against you cheek

Riddle me this Bat Idiot (designer): is my gunstock a cylinder? No? then how come this sleeve is a perfect cylinder that's too tight to go over the end of the smooth buttstock of my M16 A1 retro clone AR15 and loose as a goose and has to be cut off at the narrow part of the stock so that it doesn't resemble a very loose woman's camouflage skirt in that area? and it takes incredible strategy and planning to get it on and an insert in it because unlike what the pictures suggest,THERE IS NO POCKET TO THE INSERTS IN THE SLEEVE!.I could reveal my successful strategy for getting the sleeve on and the insert in, which is basically the same strategy as getting it on, however I don't want to encourage anybody to buy this phony POS. I will GRUDGINGLY say 1 thing positive: the material is VERY strong given the pressure I had to exert on it it to install it and it not ripping at all.

My Benelli m4 has a fixed stock and I needed a slight cheek riser so not to break my cheek weld with my red dot. I saw after market risers that required switching out the OEM stock that I didn’t want to bother with so figured I try this less expensive solution out. So far have been happy with the product. Has held in place just fine during range use. Time will tell how the elasticity and durability will hold up after repeated use.

Easily fits to my rifle and easy adjusting

So far it's what I expected, fits well, looks ok. I haven't really had the opportunity to test it that well. Seen that it's in the middle of winter and there's an ammo shortage . However I have tried it out twice. And it fits and feels fine .

vsr-10 に装着とても良いいいです

Poor design. The cover did not fit the stock at all and one of the foam riser pieces was missing. Returned.

Works for what I needed, but it is still slightly loose around the stock and occasionally moves a little bit.Even with some pretty intense bushwhacking it never fell off, but I did have to remember to readjust it before shooting after my hike in.Still can't beat it for the price