American Standard 047107-0070A Flush Valve Assembly

I was able to successfully use this American Standard flush valve to replace a 30 year old leaking Curtain #50 flush valve in a 30 year old high end Kohler toilet, thus saving me a ton of money. The Curtain #50 valve is the big heavy brass and copper canister style valve that was always expensive and has now become very expensive (if you can even find parts for one). I was looking at having to replace the whole toilet. I actually stumbled on this solution watching an online video. Amazon always deletes my external links in reviews, so if you are interested, go to a popular video site that begins with the word "You" and search for something like "American Standard - Removing Curtin 50 Canister Flush Valve". There are a few tricky things to know about. First, completely remove the flush handle and lever assembly from the tank (if you have a camera you might want to take a picture of the rigging for when it comes time to replace it). You don't want to take a chance on damaging this because the old style ones are hard to find and expensive. I had to cut the vertical copper rod connecting the lever to the canister. Second, the whole barrel of the canister unscrews from the seat (the lowest part screwed into the tank). Trying to unscrew the screws just causes them to spin and even if you are successful the big nuts underneath will fall into the innards of your toilet, which you don't want. Unscrewing the canister requires strength. If you are not strong you will need likely need some help. Once it is out you can access the nuts holding the seat to the tank. Third, this new American Standard valve will not use the old Curtain #50 holes in the tank. You will have to plug the three holes. I found stock rubber plugs from a plumbing parts house online (couldn't find on Amazon, unfortunately), but you can make your own from rubber or cork. Fourth, after you install the new American Standard valve you will need to use a little creativity to figure out how to attach the chain to the old lever. I used a brass bolt, two brass washers, two same diameter rubber washers, and a brass nut. I put the bolt through the groove of the old lever and slid it to the desired location over the new valve I then wrapped the chain around it, cushioning and gripping it on both sides with the rubber washers. I used the brass washers at the bolt's head and nut to hold it all together. With a little trial and error I got the chain at the optimal length and position along the lever. The rubber washers grip the chain well without causing any damage. It's been over a year now and everything is still functioning perfectly. In the meantime I fixed a second toilet using the exact same valve and procedure. This valve is versatile and turned out to be a lifesaver for us. Oh, one more thing. The guy in the video, when installing this new American Standard valve, used WD40 to clean the old surfaces and to prep the new rubber gaskets. I found this to be a mistake. When I did this the WD40 contaminated the whole tank and made the parts too slippery and the new American Standard valve leaked. It was very annoying to be woken up in the middle of the night with the tank dripping and the fill valve running new water in every half hour. At first I thought the new valve was defective then realized it was probably the WD40 causing the problem, which it was. After I rinsed the heck out of the tank and parts the new valve worked perfectly. I didn't make this mistake the second time. Hope this info helps somebody.

It’s amazing that the flapper valve assemblies on our two American Standard one-piece LowBoy toilets would last for almost 40 years without replacement. Even the ceramic toilets themselves still look like new… good quality! However, both toilets began to leak about the same time, apparently because the surface of the soft rubber flapper disk was disintegrating. Amazon.com to the rescue… the correct parts for these old toilets were easy to find on the web site and delivery was amazingly fast with Prime. The parts received were in American Standard Genuine Part packaging (not a knock-off) and the high quality of the molded/machined plastic parts and gaskets was obvious. Removal of the old parts and installation of the new ones were quick and easy. The replacement immediately corrected the persistent leak problem and the toilets have been operating great for almost a month, so maybe I can expect another 40 trouble-free years from these toilets. Removal and installation were easy, but here are some notes that might be of use… If you own one of these toilets, you already know that the rubber-disk gasket and seat in the separate filler tube are the most likely things to wear out and cause leaks. The rubber disk deforms and will no longer seal and/or the sealing edge of the (plastic or brass) seat can erode from water flow and grit in the water (hard to see unless you remove the seat for close visual inspection). Make sure that these items are sealing properly before blaming the flapper assembly. A good way to determine what is causing your leak is to turn off the water at the inlet pipe to the toilet, check the water height in the tank and then come back later and see if any water has drained out of the tank. If the water level goes down, you will have to replace the flapper assembly (if the assembly is still relatively new, you can purchase the rubber flapper disk separately, which might fix the problem at a lower cost). Makes sure you order the correct flapper assembly. There are two types, with the only apparent difference being where the beaded chain attaches to the large cylinder on the flapper. P/N 047107-0070A (this review) has the chain attached near the top on the side of the cylinder, but. P/N 047250-0070A is closer the center of the side. There is also another (after market) flapper shown on the site that apparently has a brass seat (not plastic) with a rubber flapper mating surface and is separate from the actual flapper assembly – they are screwed together in the final assembly. Order the type that looks like yours in the pictures. Use care when you remove/install the beaded chain from the clip on the flush handle rod. If you damage the clip, there are NO new clips included with the replacement assembly. Do not attempt to remove or install the seat portion of the assembly without first removing the flapper assembly by carefully spreading the plastic attachment (hinge) tabs on the seat, tilting the flapper assembly to disengage one of the cylindrical pegs and then tilt the assembly to disengage the other peg and lift the assembly out. You will now have free, unobstructed access to the three screws that hold the seat in place in the bottom of the toilet tank. The seat portion of the assembly is held in place with three large (stainless steel) screws that fit into threads of rectangular (brass) blocks. All new ones are included with the replacement. The old screws will probably be frozen in place. However, the seat can still be removed by using a large #2 Phillips screwdriver with firm downward pressure to turn the screws and blocks together. A 180 degree turn of the screw will rotate the block out beyond the ceramic lip holding the assembly in place in the tank. Do this on all three screws and the entire seat will lift out easily. Before installing the new seat, clean-up the surface where the old rubber seat gasket was in contact with the tank. Put all three screws into the appropriate holes in the new seat and screw on the threaded brass blocks enough to hold them in place, but not too loose so they might fall into the toilet during installation. Rotate the blocks inward so that the assembly can be inserted into the hole in the tank (remember to install the large rubber ring gasket on the seat assembly before installation). After the seat is inserted, rotate to align the two tabs that will hold the flapper assembly into the correct location (left side and parallel to the tank sides). With your fingers, carefully rotate the blocks outward under the ceramic tank edge until they are perpendicular to the edge and then carefully snug-up the three screws so the blocks will not rotate during final tightening. Now, gently tighten the screws sequentially in small increments until they are all uniformly snug. Do not over tighten them or you may crack the ceramic tank. Now all that is left to do is reattach the flapper assembly by carefully spreading the seat tabs to accept the hinge pegs of flapper assembly and connect the beaded chain to the clip on the flush handle rod. The location of the chain may need to be adjusted so that it tight enough to properly actuate a flush, but not too tight to cause the flapper to lift and leak. Open the water valve to the tank and refill. Adjust the chain as necessary and check for leaks. Put the cover back on the tank and be sure the flush lever will actuate a flush correctly and the flush duration is long enough to empty the tank. Some reviewers have stated that the flush length is too short, so they have had to add small weights inside the cylinder that is filled with water and then empties through a metering hole to increase the flush time. I did not have this problem. Happy flushing !!!!

Replaced it for my 20+ year American Standard. Fit like a glove. Saved me a plumbing bill!

My girlfriend has an expensive one-piece American Standard toilet in one of her bathrooms which was not functioning properly. Plumber said it was a discontinued model and not possible to get a replacement valve, so she had to replace the toilet. I called BS on that and searched online. Found this. Install was easy. Only reason I didn't give 5 stars is that it came with no instructions, and I could have installed it much faster if I had simply understood how the fastener system was designed.

Well, "love" might not be the right word, but it did prevent me from having to completely replace a toilet in my house. This is a direct replacement for the American Standard "Master All in one" toilet flush valve assembly. While the original one (60+ years old) was a metal flange and everything except the stoppers and floats were metal, this worked just fine. Just be careful not to tighten the screws down too tight or you might bend/break the tabs that hold the valve to the bottom of the tank area. Anyways, replacing this fixed my 20 gallons an hour leak on my toilet. ***The one thing that you might want to look at is the top "float" that fills with water and when you flush it slowly drains the water from it thus allowing the flapper assembly to close again, it seems to take a long time to drain and keeps the flapper open for quite a while after the water has drained from the tank. Looking at the original assembly, the hole in the bottom of that piece is a little larger, allowing the water to drain faster and the flapper to close sooner, not using as much water. I left mine as original for now, but will probably end up drilling the hole out a little more to try and save water.*** Either way, this bolts up fine and have my toilet back working as it should in about 10-15 minutes.

I have to replace these every couple of years because my water is so bad that it deteriorates all of the parts in my toilets very fast. I don't use any chemicals or bleach in the tanks because there is so much chlorine in our city water. I have 3 of these toilets in my house, so needless to say, I've been spending 75 bucks a piece at the local plumbing supply for years. I recently found these on Amazon and ordered one. I received it fast and was very pleased to see that it was authentic American Standard parts boxed in an American Standard box. I have used other after market replacement parts and they just don't work as well or as long. No more trips to the local plumbing supply for these. (They're going to miss me...) I am finding other parts are much cheaper from Amazon too... Thanks Amazon, you're awesome..... Don't be afraid to install these parts yourself and save a bunch of money. Hope this helps if you haven't done one before. I just turn off the water at the toilet valve and flush the toilet holding the handle down until most of the water is out of the tank. If your toilet has been flushing well, take note of how the chain is adjusted when you release the handle before you remove any parts so you can replace it in a similar fashion. Now remove all the water from the tank, so you can clean everything inside well. I use my shop vac and it only takes seconds. If you don't have a shop vac handy, just sponge or towel the water out. Remove the flap float by spreading the plastic ears and rocking it until you can remove it and separate the chain from the holder. Use a screw driver and loosen the three screws, leaving the ears on the screws so that you can remove the seat and gasket without dropping them inside the toilet. You will re-install the seat in the same fashion. Clean the seat surface of any debris, use a scraper carefully so as not to break anything. Remove the new flap from the new valve seat before you start to install it. Start the screws and retaing ears on the new valve seat and place the gasket on. Place the seat down inside and turn the ears under the china tank so they line up. Carefully tighten the three screws alternating to each one making sure to slowly tighten the seat evenly. Snug is good, be careful not to break your tank by over tightening. Now install the new flap and float assembly and hook up the chain. I always install a new fill valve at this time, but you don't have to if it's working well. When everything is hooked back up, turn on your water and check the adjustments. I am not a plumber and this whole process only takes 20 minutes or so, depending on clean up. Good luck and give it a try. The only mistake most people make is they over tighten their plumbing parts and ruin them. So go easy, because you can always tighten parts a little more if needed, but if you over tighten, you have probably ruined something.

This unit was easy to install (took only about 15 minutes to remove the old one and put this one in. It seems to have stopped the periodic refilling caused by a small leak at the disc (which we had replaced numerous times over the years but never really resolved the issue). An important additional benefit is that replacing the entire unit enabled us to eliminate any need to double flush, which we have been putting up with for many years - the reason is that this new unit stays open until the tank is fully drained, handling all flushing needs. We hunted for a solution for years, but when we found the pictures of this unit and its dimensions on the Amazon website ad for this unit, we finally understood how it is installed and that it would be the appropriate solution for the slow leak in our 30 year-old American Standard one-piece toilet - THANKS Amazon for posting those pictures!

Easily installed two days after delivery was promised. It’s lightweight so I don’t expect it to last more than a few years but for now it’s serving it’s purpose even though the delivery was not next day as advertised so if you need it ASAP you’ll have to wait. Otherwise it’s an acceptable product.

Well made and easy to install. The Lexington flushes like new.

Did not use this device as it did not come with a return spring. - So instead I bought a replacement from Screwfix for UK Syphon system which was supplied with return spring - works beautifully!

Excellent product...functions and good quality.

Easy to install. Do not need a plumber, just a screwdriver.

This was purchased to replace the original equipment and it was awesome. Fit perfectly and easy to install. Every flush is now twice as satisfying as this flapper executes the operation perfectly and consistently.