Pioneer KWIK-E-VAC Line Set Flushing Kit Installation Simplifier for Mini Split Air Conditioning Systems

Purchased this to install a pre-charged 9000BTU Della Mini Split for our Master Bedroom. (simple install by the way) I was tempted to buy an evac pump kit because I needed to upgrade to a 25-foot line to reach the outdoor unit. But then I came across this product. I flushed the lines according to the video that was available by scanning the QR code on the box. It was simple to do. I am getting 115-degree air on the heat and 48-degree air on cool, which is amazing for a nonprofessional install. I HIGHLY recommend this for the DIY install. And the Della Unit is awesome and very quiet. Hope this helps.

Used to charge my new mini-split. No need to pay an HVAC tech to do the job.

Worked great. Watched a couple of youtube videos on use. One challenge is knowing when you've flushed the line. Even though the can is supposed to be enough for a couple of installs, I only had one to worry about, so I used most of the can. Per the instructions, I started with the smaller compressor line off the fitting, let the Kwik E Vac vent into the service port for perhaps 20 to 30 seconds, and then slowly started to thread the small line onto the compressor port; I left it a little loose so I could still hear the escaping gas from the Kwik E Vac can. I didn't tighten it until the escaping gas noticably slowed down, and then I tightened it fully, feeling comfortable I had used most of the can and the line was fully evacuating of air.Was rewarded with a nice, cold airflow from the inside unit the first time I fired it up. Install is in a shed serving as an office. It was in the mid-seventies outside, and I set the unit to 68. It cooled it down very quickly. Tested the heat on a cool morning a few days later, and the unit blew nicely warmed air.This product works, as long as you do your part with properly fitted connections on the coolant lines.

This was a lot easier than the idea of buying another pump I was going to use only twice. The last one I bought was years ago for an a/c install, never used it again and gave it away. Because I live and travel and work out of a converted school bus, I am not the kind of person that holds on to things I don't use often. I don't have the room for extra junk. These cans were quite convenient. This was for an install of a mini split unit to my bus, in fact. I couldn't use the whole can simply because the inside unit came pretty much pre-charged with flushing gas. Still, I used about a half of this can and followed the directions. Couldn't have been easier, and my unit works flawlessly. I will be looking for these again especially since several others want me to do their mini split install now.Update 7/11/2021Fortunately for me, I forgot to torque one of the lines on the outside unit and all of the coolant slowly leaked out. First, the inside unit started freezing up, and a few days after that started, it wasn't able to really cool at all. It wasn't until I had time to look at everything that I remembered I never fully torqued the outside connections. Usually when the coolant can leak out like that, that means some air likely got in as well, so I just evacuated out the remaining coolant, vacuumed the system with a 1/3 hp vacuum, and then refilled the coolant (from a 25 lb tank of r410a) according to the service manual.I immediately noticed that the inside unit was blowing FAR cooler than what it did when first installed. Yet, there was absolutely no ice. Everything was perfect. The thing is, I'd bought and installed two mini splits using this stuff on the bus I'm converting to an RV. The second one was still working, but I couldn't help but notice it simply wasn't as cool as the newly repaired unit. I was going to just let it go, but I couldn't. I evacuated the coolant from that system, vacuumed it out as well, and then refilled it too. The difference? When the temperature reached 92 degrees yesterday, I had to turn the air up to 72 because my toes were starting to hurt (I used to always leave it set at 68). My toes hurting says a lot considering I'm a diabetic. I used to schedule my units to switch to 68 degrees around 8 AM and around 9 PM, set to 70 so I won't be too cold. Last night, I had to set it to 73 to not be too cold. It wasn't cooling outside of its range or anything. It just turns out when two units are working at 100% and can truly cool everything down to under 70 degrees, that's a bit chilly.So, I won't try to take any shortcuts when installing or repairing any of these split units. No more flushing kit in a can. I'll stick to good old fashioned vacuuming because had my one unit never leaked everything out, I would have never known these units could have been doing so much better.

It seemed fine. The valve and hose I got seemed much nicer than what was shown on the amazon page for it and may have been improved to solve the problem others reported here in the reviews. I used this to help find leaks in a system I installed but had not yet started up. One of the 3 line sets showed a leak during a vacuum test and I used this item to pressurize the line set and I put soapy water on the fittings to try to find the leak. It didn't work right away but after tightening a couple of the flare nuts the bad one started bubbling and I knew that was the leaker. In hindsight I could have just redone each flare and retested but it ended up being the last flare I suspected. If you're DIYing a mini split buy the vac, the manifold set, and the Yellowjacket flaring tool. The cheaper torque wrench seems to have been a waste of time but the rest of it is invaluable.

Best kept secret! Not a plumber here. Had a friend tell us about this. Used this to install a 12000 btu split system to avoid needing a vacuum and pressure gauge. Worked perfectly! No need to pay a plumber hundreds or buy weird equipment.

Item arrived as advertised,Thank you.Regards,J.G

I had to adjust the valve to get it the flow with enough volume it wasn't plug and Play