Cressi First Dive Mask with Inclined Lenses for Scuba Diving : Focus: Made in Italy

This product worked great for me. I was able to get a "prescription" corrective Cressi lens for each eye. Get your scrip and reduce by 0.25 (how much water magnifies) and round down nearest 0.5 stock lens size. I used correction lens of -4.5 left and -4.0 right and it worked fantastically for me.I got a good description and the suggestion to use a cell phone pry tool on a dive forum and also watched a YT video to change out the lenses. The plastic pry too worked great and if you review where the tabs are you can disassemble and substitute the lenses very straightforwardly. There is no astigmatism correction on the lenses but under water is wasn't noticeable for me.The mask itself fit my smaller face very well. It looks a little large on the face for me. Although a dive mask seems a little overkill for a snorkeling experience, the total expense was completely worthwhile. If you can't see the shape detail of tree leaves without glasses, you aren't going to see much underwater for small fish, coral, etc. This mask is a great option for nearsighted people. It's also surprisingly well made for something that is all plastic framed. I purchased the same mask for my husband. Size looked right on him. He has a longer narrow face compared to my round one. Fit him ok, but not perfect. Overall pleased with quality and the option to add lens correction.

Like this because you can manually add in vision lenses based on your eye Rx diopter. Can buy lenses separately much cheaper than a custom RX scuba mask. Google videos on how to disassemble the mask to swap the glass with the corrective lenses. Was easy to do. Been using this mask without issue for a long time!

Works great with replacement lenses! That's the neat part - good to see clearly underwater. Nice that the mask is economical, because the lenses will cost more than the mask (the mask does have Plano lenses in it, for those who do not require the prescription-type lenses). Also, once you put replacement lenses in, you may likely find that you cannot read your gauges anymore if you are older and require reading glasses. In this case, you can also add the stick on Dive Optix - the whole rig then ends up being around 140 bucks - but it is likely much less expensive than getting a custom ground setup? The one negative is that they don't give you ANY instructions on how to change the lenses on this mask. I had to figure it out. The browpiece (with Cressi name) slides straight up, with the help of a little screwdriver. hard not to get a nick or two during the process! Then, you will see tabs under the browpiece for each retaining ring. Carefully lever under those and pop the retaining rings out. Then you can push out the lens from the underside (diver side), being careful not to disturb the silicone seal the lens rests on. Put the new lenses in and reverse the process - and you are good to go!

purchased one for my son and he loved it so much that i bought one for me! for the lenses, I subtracted .5 from our prescriptions and they both turned out very good.

The lenses fit the Cressi Focus mask just fine, and it's a good mask.I'm deducting TWO stars because of the incredible frustration trying to figure out how to install the lenses in the mask. A single sheet of paper with a couple of illustrations would be so easy to include, but there is nothing!Once you understand HOW to remove and replace the lenses, it's pretty easy. But it is NOT intuitive, and I couldn't find anything online that explained it clearly.FYI, here are the basic steps:1. There is a small triangular piece of plastic at the top of the nose. This must be pulled straight out, as you look at the mask. You can see behind it that there is a little tab. If you push the tab towards yourself with a small screwdriver, that will push this piece out.2. There is a bridge (where a "uinibrow" would be) with the Cressi logo on it just above the piece that you just removed. That piece needs to be pushed straight up, towards the ceiling as you face the mask. It's just a friction fit.3. Here is the hardest part to figure out: the two plastic rings that hold the lenses in place. You can't just force them out. If you look carefully at the front of the mask around the outside of the two retaining rings, you'll see three areas about 1/2" long each, which is where there are little plastic tabs that stick out from the retaining ring and hold it in place. The ring is somewhat flexible, so all you need to do is get a fingernail (or something) on the outside of the ring near one of the tabs, and push inwards towards the center of that lens. This will get the tab out of its slot and allow you to pull it forwards slightly away from the lens. Do this for all three tabs.4. The old lens pops out at this point and you simply set the new lens in its place.5. The only tricky part about putting it all back together, is that you really need to exert some force when pressing the retaining rings back into position against the face of the lenses. The tabs need to snap back into their retaining indentations. If you put the mask face-down on a table, you can press down on the inside of the mask and that will help force the retaining rings all the way back into position.6. Now it's easy: simply replace the "unibrow" piece by pressing it straight down from above - you can see the plastic part of the mask that it slides down onto.7. Finally snap the little triangular piece back into position by pressing it straight in. Again, after it's out, it's easy to see how it goes back in.Sheesh, why couldn't Cressi have included this little explanation along with a few line drawings with their mask and/or lenses?

I'm very nearsighted and was dreading the cost of ordering a mask through my optician's office. This mask - along with the pop-in prescription lenses (sold separately) as a lifesaver! Great quality, great value, and I could see perfectly underwater!

I absolutely love this mask, when I first started wearing it - I was extremely frustrated! It was constantly fogging up.I thought perhaps I had the wrong mask for my face or I was doing something wrong.After going on You-tube, I discover that all mask needed to be scrubbed with toothpaste to remove the protective layer that is on all goggles when they come from the manufacture. This film is applied to the mask during the glass cutting process. I was afraid to do it myself so I took it to the dive shop and they scrubbed the inside of the lens with toothpaste and a toothbrush several times.Once the layer was removed I simply spray a layer of anti fog inside the lens, a quick rinse and they worked perfectly. Absolutely love them now. Put then on and off several times during my 60 swim and No Fog - No Leaks! H

Me gustaron mucho, ajustan perfecto y el silicón es de muy buena calidad. Excelente opción si son de tus primeros visores.

uzun yıllardır kullandığım bir maskeydi indirimden bir tane daha aldım.Malzeme kalitesi çok yüksektir, maske iç hacmi düşük oldupundan buğu sorunu yapmaz

Ürünü kesinlikle tavsiye etmiyorum. Buğu yapıyor.

...But very good glass, easy to remove fog and holds clear. Adjusts really well and over all good quality.