BlueStars WR60X10185 Evaporator Fan Motor for G.E & Hotpoint Refrigerators - Replaces WR23X10353 WR23X10355 WR23X10364 PS1019114 AP3875639 WR60X10043 WR60X10154

What can I say, it works. As far as the life of the motor, I cannot say, but since the GE model does not last a long time, it couldn't be much worse. I bought two, so that when this ultimately gives out, I am not hard pressed to find another. It fits perfectly in the holder and the fan blades fits on the end of the shaft just like the original.

It works. I replaced the motor. I had to cut and butt the wires for the light. Now the fridge and freezer are running great.

The house we bought had a built-in 48" Jenn Air refrigerator (JS48PPFXDA) that was ~20 years old - and on the decline. Temperatures fluctuated, but we determined we could not use the freezer side anymore, as it would get up to 50 degrees, and never lower than 30. After dealing with this for more than a year, with it getting progressively worse, we decided it needed replacement, but a new 48" refrigerator was not an option.Took apart the freezer and found that there was ice all over the wiring - so it was getting cold enough, just wasn't getting the air down to the freezer section. The evaporator fan motor (Panasonic UDQT26MT6, Jenn Air part 67003241) wasn't working, and was discontinued.After much searching, and consulting with a local appliance repairman, I decided to order this one, even though it's a 9.5V, and the old one was a 12V. It was the same 4-wire configuration, and had the same sized/shaped wiring harness connector.Installation was relatively straightforward, but it didn't connect to the wiring harness very easily - have to push pretty hard. That said, it's not listed as a replacement for my machine, so I can't complain there. Also, the pin that the fan blades mount on was about an inch longer than my old one, so I cut it down to size with an angle grinder and filed the cut edge smooth. Put it into place, connected the wiring, pressed the freezer door switch (as if the door were closed) and waited about 15 seconds. Finally, it kicked on, and it worked!This afternoon the freezer temp is reading 5 degrees - it has never gotten that cold while we've had it! And now that the cold air is getting down where it needs to, and is getting pushed over to the refrigerator side, the fridge gets to the upper-30s where we set it, instead of also being in the low 50s.All things considered, this was a ~$20 part that saved me from spending a couple thousand dollars. Hopefully it will last a while.

I purchased this to replace the original fan in our GE Monogram refrigerator. After several months in operstion, the fan is working as expected. The only initial issue was that I had a bit of trouble installing the fan, i.e., the electrical connector did not lock in very easily. I had to used channel lock pliers to get the connection locked. Also, the fan is much louder than the original fan. The primary benefit is the much lower price for this replacement part vs the OEM model.

Worked great. No harness accessories included (pushpins, thermal insulating tape etc.)

I usually don’t leave reviews however I think this is very important.Please do not buy this product. My fridge is almost went broken because of this installed product.The fridge’s motherboard was almost burnt. The product worked for couple hours and stopped. I had to call the technician twice and pay for the service twice.

We ordered the Evaporator Fan Motor Replacement Part from Blue Star because it was the best deal. It has been running in our refrigerator for 4 days now and it is doing a great job.

My refrigerator started making noise and I isolated it to the Evaporator Fan motor. used partselect website to find the replacement part number and a video on how to replace the motor. The Part on Amazon was 1/3 the cost and the quality looks to be the same as the original. The old Fan blade and rubber grommets were in good condition and i did not need to replace them. I had to remove the ice dispenser motor assembly and Ice maker to gain access to the evaporator Fan module. The are easy to remove with only one or two screws holding them in place and a couple electrical harness to disconnect.The new motor electrical harness only has 4 wires. My evaporator fan module however has a light and has a 6 wire electrical harness. I had to cut the 4 wires off the old and fan motor and then splice the new fan motor in.The whole job took me about 1 hour but i went slow and took my time.