SBFT-160004H 160mm 4 Tooth FesPro Fiber Cement Cutting FTG Saw Blade with 20mm Arbor for Festool TS 55 EQ, DeWalt DWS520, and Makita SP6000K

I've bought 11 of these blades for my Festool TS55. They are always razor sharp, leave a great cut and last long. We do custom millwork and I always keep a spare blade in my box in case I saw through a screw.

I used this blade to cut down finished cabinets and it worked great with no chipping.

I'm a big Festool fan. Well, I should say that I really like the Festool products that I currently own. I've owned a few green tools that....well.....sucked. The track saw is one of my favorites. Yeah, it's a little underpowered when cutting bevels but I rarely use it to make these cuts. One thing, IMO, that Festool doesn't do well is make blades. I've owned a couple of the Kapex saws and the blades provided are pretty sad. The fact that they provide a 60T blade with a $1400 miter saw is ridiculous. Do they really think someone is using this saw for something other than finish trim??? Sure it has a negative hook but still.... Back to the Oshlun blade. It cuts great. Super clean cross cuts and plenty fast when ripping 3/4 ply. I highly recommend this blade and will be purchasing another. I purchased the 80T for my Kapex and it's a great blade as well.

I bought this as a replacement for the Makita 36v track saw. It’s definitely and small downgrade from the factory blade. The kirf is thicker, the blade is slightly smaller in diameter, and the arbor is slightly smaller but it still fits the saw. It worked fine but the cuts weren’t as smooth and the blade seemed duller then original Makita blade thus putting more strain on the saw and operator. Ripped the wood a little on crosscuts too. Maybe it’s meant as a replacement for Festool. It’s good value for the money, but I think I’ll be going back to Makita.

While i was worried that i would not be satisfied by these less expensive blades, i have been happily surprised. They are a great alternative to spending top dollar for Festool blades that are frankly a bit overpriced. I'd love to see the actual cost compared to mark-up on saw blades. Using a sharp blade saves time, improves quality and pleasure of work imensly. The option of Oshlun blades is a wonderful thing about capitalism, which usually is not so nice. While i might not use them on every job, 90% of the time they do a fine job and I see no difference (besides price) from the Festool blades. Recently I used a not new 48T Oshlun blade while ripping "Hardy Plank" I did a good 10 8 foot rips of the silica concrete board. I think the blade is toast, but even during the final rip it performed more than adaquately. I continue to be impressed and pleased with these blades. I'm lookin forward to see how they sharpen, just for kicks, I'ts probabaly cheaper to toss them, but my sharpening service does a great job, so it will be a worthwhile experiment.

I used this blade and a Festool track saw and finished 2500 sq feet home install hardie plank siding it’s an amazing cleaning cut save about $100 chapters then Festool brand

I was searching for a cheap blade for my Makita battery saw when I found this one that fits the Festool. Turns out to be perfect for the job. Not only does the blade cut just fine, but I hooked up the cyclone dust collection / vacuum and didn't have to breathe cement dust. Cutting the fiber cement didn't really do anything bad to the saw like I thought it might. Good blade but even better if you have the stuff to suck up the dust.

So I "ran over " a steel bench dog with my Festool blade... Boo hoo my bad. There goes $80. Lesson learned, I'll buy a replacement. Here's an alternative... Hmm $24 for a similar tooth blade? Why not give it a try? Well glad I did! Great cut in 12mm birch plywood. Nary a scratch on the edge and splinter free--just like the $80 Festool blade! Now to stay away from those bench dogs... HIGHLY RECOMMENDED BLADE!

Started using these blades when I needed to replace the OEM Makita blade. I use if for a lot of different materials, primarily breaking down plywood but I also use it when installing Trex decking. It works well and the first one lasted longer then I expected it to but I do clean the blades regularly which I think helps. It's a solid option.

For a much cheaper alternative to the Festool blade which in Australia is around $180 mark, I cant fault this blade. It does well.

Excelente producto

I bought a replacement Tracksaw blade on Amazon for the dewalt Tracksaw and it just didn’t fit properly. I bought this one hoping for better and it’s perfect. Great sharp blade and works great in the Tracksaw with no binding which I was having with the other blade. I will be buying more.

Good blade and a lot cheaper than the dewalt one. The only thing to keep in mind is the kerf size. Original is a hair wider than the oshlun. But it dosent affect the cut at all, the splinter guard does it job perfectly. Cut quality is verry good . I cut red oak 1”inch thick for a new stair case and it was a charm using it.