AmeriLite Black Projector Replacement Headlights LED Halo Set For Toyota FJ Cruiser - Passenger and Driver Side

Installed 2 weeks ago, great so far. Pretty much plug and play. Here are a few things to share: 1. Quality seems good. Materials feel mostly on par with factory. "Made in Taiwan" labels on box and product 2. Same mounting points and plugs as factory (besides the DRL's). Easy plug and play 3. Same vertical and horizontal adjustment screw locations as factory and both can be adjusted when fully installed. Horizontal screw is near the top with easy access to adjust. Vertical screw is much lower and requires a long phillips screwdriver inserted through a hole near the top mounting point to reach, exactly like factory. See attached pic. 4. Mine required moderate amount of vertical and horizontal adjustments (and maybe even rotations, but I didn't see a way to adjust this). Out-of-box, they were pointed way too low and "toed-out". There are plenty online videos on how to aim your headlights. Attached pic shows after adjustments (with LED bulbs). FYI. These are labelled "VOL". See attached pic. This means you align vertically to the "left" of the cutoff "step" 5. Comes pre-installed with 65W H9 halogen bulbs which were still quite dim. I switched to these 60W H11 LED's and they're a lot brighter, much brighter than my BMW factory LED projectors: https://www.amazon.com/dp/B0FDK7Z7GY. See attached video 6. Low and high beams use the same bulb. High beams just lift the mechanical cut-off out of the way. Everything works properly out-of-box on my 07 7. The LED halo DRL's come with separate dedicated bare wires (+/-). You'll need to figure out the rest. I measured about half Amp draw per side with a multimeter. So they draw ~6-7W each side 8. I made custom wires with waterproof plugs to connect left and right DRL's to the DRL fuse (#13) in the engine bay using add-a-circuit fuse adapter: https://www.amazon.com/dp/B0742BZXC2. See attached pic. Since both DRL's draw ~1 Amp combined, I used a 2A fuse. I also disconnected the factory DRL circuit plug behind/below the driver-side headlamp. New DRL's now come on automatically just like factory. 07 does not have a DRL switch on the stalk, they just work automatically so not sure if this installation method would work on other model years. See attached pic of DRL's running automatically without any other lights on. By the way, DRL's are bright and very visible in broad day light but do not use them as low beams at night as they would not light up the road

Love the way they look. Significant improvement to light on the road. I choose these to keep the retro type look to the FJ. I’ve had it for about 5 years now, it’s about time I made some of these mods. Has DRL, lo and high beam. It looks like that’s just a change in the shutter positions to let more light out. I have my DRL unplugged so I tapped into the parking lights for my LED power. I used these 2in-2out wire connectors. I chose to do it close to the light. Figured it would be easier to add a plug back on than to splice wire if I ever take it off or replace them.

Good quality lens

The high beam does not work. It is not an issue with my FJ. The hi beam works with original lamp, but not the lamp that was included. UPDATE: It appears FJ Cruisers with that do not have the DLR feature are incompatible with this product. Amerilite was very helpful and tried to work out several solutionsbut unable to solve the problem. Iitem is being returned.

This headlight looks good once installed. It needs instructions on how to connect the halo lights. Here we go: The package has connector that connects to existing headlight connector plus two wires, one black and the other red. Connect red line to hot wire (mine was green line) for the turn signal light and black line to neutral line (center wire). Plus, center light is only for the high beam. This unit uses the halo light as low beam and center light as high beam. So, when you turn on daytime driving light, it turns on halo light. When you turn on headlight, it turns on center light (high beam). When you turn on high beam, only halo light is on and center light turns off. Hope this instructions help next buyer. From one FJ lover to another FJ lover!

These replacement headlights sets are sooo bright and wonderful out here in the country where deer are everywhere and the road are not lit for miles and miles!!!!! I couldn't be happier with these for my Toyota FJ Crusier!!!!!!!! Love them!!! The price is well worth it, fast shipping, excellent NIB!!!!!! Easy to install!!!!!! They jazz up the look as well with the O block design (GO BUCKEYES!!)

I was planning to get the Freedom retrofit, but their prices were too high, and the wait time was about four months. Instead, I bought these lights, and they turned out surprisingly good. These lights are made in Taiwan, and the quality is much better than the parts made in China. The fitment is just like OEM, but the plastic is a bit softer compared to OEM. The installation was easy, and it took me around 30 minutes to install from hood open to hood close since I have worked on the front facia before. I replaced AmeriLite's halogen H9 bulbs with LED bulbs and did not connect the halo ring for now, but maybe I will run them later. These lights provide a clean cut-off, so I don't blind incoming traffic with the LED bulb. I only wish they spread a bit wider, like 10 degrees more on each side. I applied Lamin-x film for UV protection. Let's see how long they will last since they only cost 1/4 of what Freedom retrofit charges (Freedom uses OEM housing and Mishimoto light units???) ***March 2023 update, The Halo lights have been wired up for a year now, and so far, I have not experienced any flickering or dimming units. Hopefully, it will continue to work without any issues (knock on wood).

BUYER BEWARE The bulbs for these are NOT H4. They are H9.