CC3D PETG Pro Filament Blue Gray 1.75 mm 1KG 3D Printer Filament 2.2lbs Spool 3D Printing Material Fit Most FDM Printer PETG Blue Grey Color

When I had the first bulk order of my keg-coozie design come in , I was forced to find an alternative to the metallic-grey PETG that I had been using due to the other seller not having enough stock. I've struggled with finding a nice opaque, metallic, not too glossy grey in the past; But this filament was just what I needed! A slightly lighter gray tone, less plasticky "gloss" while still maintaining a metallic sheen, and even 20% cheaper than the one I had used previously. I was, however, concerned about the quality causing issues during the printing process; because I had a tight timeline to maintain for this project. I ordered an extra 2kg to account for any issues (14kg total) and saw my whole order arrive quickly within a week. All in perfect condition, all 14kg the same color with no variation, and I was pleasantly surprised with how good of a match the color was (the online photos make it look even a shade lighter than it is in person). Printed on 2x Bambu A1 Minis at 240c nozzle/ 70c bed; no drying prior to use, printed within 48hr of opening; I was able to print 50 plates/10 hours each with only one failure! (clearly due to my design plus low infill; as it occurred with my previous filament as well and has since been corrected). I only ended up needing 12kg, but have since switched to using this filament permanently for this design. All 14kg printed very well with no noticeable variation in quality throughout the batch. The only thing that I could say as a negative was that a good few of my prints had minor surface defects (hair-like stringing and some tiny dimples that can be wiped away without significant marring to the surface). I simply waved a torch over the strings and then wiped them off with a cloth rag. This may have been avoidable with adjusted settings, but I had no time to experiment and the issue was very minor. Well worth the price and a great metallic grey to have on hand; Thank you to the seller for maintaining a high enough stock to fulfill my order in such a timely manner!

I am not sure why it's so hard to get gold color right. First I ordered a roll from Overture and it came out more like mustard. They seemed to think it was correct so I had to return it. Then I came across this one and was even less expensive. So glad that I got this one to try. First of all, I have never had another spool of filament came with bubble wrap inside the packaging box around the spool itself. I mean it's probably not necessary but does show they went the extra mile to keep their product protected. The filament printed very well on my Creality V3 KE with only a tiny bit of stringing. That is not entirely an issue with modern high speed printers using higher temp setting to help with speed. The color is not shinny gold but more of a dull color and it looks fantastic IMHO. Adhesion is excellent. In fact my dad dropped the model in picture and a corner of the roof broke off. You can tell that layer adhesion is excellent because the break was not along any layer lines as one would have expected. I supergluded the corner piece back and you couldn't even see any break line. All in all, it's very good filament and I will definitely buy again.

The spool arrived with a minor crack on one edge, but it remained perfectly functional and spun true with no wobble. Print performance was excellent — out of 46 parts, only one failed due to a stray glob that fell into the infill. Beyond that, every print came out clean and consistent. Honestly, this filament prints just as well — if not better — than Bambu Lab’s own translucent PETG. And the color... wow. This is what green should look like. Bambu’s version doesn’t even come close. This green absolutely pops. Great price, fantastic results. Will definitely be ordering again and trying other colors. Highly recommended. Setup Notes: Started with Bambu Labs PETG – Translucent profile and made the following adjustments on a Bambu Labs P1S: Nozzle Temp: 260°C (initial), 255°C (subsequent layers) Build Plate: 77°C (initial), 72°C (subsequent layers) Flow Ratio: 0.97 Density: 1.27

I'll start with the upshot: this is surprisingly good quality PETG for this price point. All of the spools that I've purchased have ultimately printed reliably and produced high-quality prints with good overall surface finish. Unfortunately, that's not the end of the story. All of the spools I purchased also seemed to contain some amount of moisture contamination. The spools arrived sealed and went directly onto my printer, where I started having immediate adhesion and quality issues. It took a few minutes of watching the nozzle to see obvious popping and bubbling. I've noticed this problem on every spool I've purchased from this brand. The filament is usable in this state, but expect surface quality issues and tricky adhesion. That said, moisture contamination is a fixable problem. If you don't have a filament dryer, then bake one in an oven or a food dehydrator. 150° is plenty, and you'll need to keep it in for 4-5 hours at least if you're using the oven method. I suspect the bags this filament is coming in aren't properly sealed, so you might also be able to throw it in a sealed container with a handful of desiccant packets for a week. I can't reiterate this enough: the print quality from this filament is GREAT after drying. There's an issue with either manufacturing or packing/shipping, but the product itself works well. I've left my spools sitting around in the open after drying for over a week without issue, so this doesn't seem to absorb moisture from the air any faster than other PETG spools. It's not plug and play, but the price point makes this filament a pretty good deal if you're willing to take the time to prepare it.

巻き具合ももつれなく、造形も糸引き少なく問題なく使用出来ました 色も綺麗なイエローでした コスパ最高です

Lo usé con boquilla de 1 nm y se comportó bien

I am extremely satisfied with this filament; I tested it on a P1S and A1, and it demonstrated great adhesion and minimal stringing (generic PETG setting on Bambu Studio (255°C and smooth plate at 70°C). I'm using it mostly for practical objects like brackets, supports, and things that would deform with standard PLA, and overall those pieces are holding well without any problems (around 4 months up to this writing). The price point makes it very cost-effective for big prints, so I recommend it. I'm planning to continue purchasing this specific filament so I can do a follow-up update on the quality control consistency in the future.

Compre este filamento anteriormente por 319 mxn y me parecio muy bueno. No se porque el precio ha cambiado pero me parece excesivo a 900 mxn

Lässt sich super mit allen gängigen Druckern verarbeiten. Hatte bis jetzt keinerlei Probleme. Auch die Spulenwicklung ist sehr sauber