PrimoChill Vue Pre-Mix (32oz) -Computer WaterCooling Fluid - Yellow

The media could not be loaded. A lot of reviews on here are going to make you want to avoid this fluid.I don’t doubt that people have trouble with this fluid but I believe that if the proper preparation is done you will have a good experience with it.Make sure to follow the instructions and use the primo prep that comes with the bottle.Is the prep extensive and tedious? Yes.Do you have to change the fluid every 6 months? YesIs this a difficult coolant to use? It can be.But the results are worth it if you enjoy the lookMy preparation for running this fluid was completely 1.draining my system of all previous coolant2. Inspecting block fins for any clogs or blockages(any existing clogs or blocks will cause problems)3 flushing with distilled water till old coolant is completely flushed.4. Running primochills “system reboot” for 24 hours5 flushing system with distilled water untill clear with no foam. (this process takes a while as system reboot creates a lot of hard to remove foam.6. Running the included primo prep solution to loop and running for 72 hours.7. Flushing primo prep completely out of loop with distilled water and running the clean distilled water for an hour before draining.8. Drain distilled water and hook up a wet vac to drain valve to completely suck out and dry all water still in loop.9. Add primo prep into loop.After this you want to go into bios and set a custom curve for your water pump.Make sure that the pump runs at only about 2000 rpm untill your cpu reaches temps above 50cThis ensures that the fluid doesn’t get pushed through the system with too much pressure which can cause it to breakdown quicker and shorten the lifespan. This also allows for a better looking flow.Lastly as you run this fluid just keep an eye out for clogs and monitor your flow.I actually received lower temperatures with this coolant than the opaque fluid I was running prior.If you are meticulous with your prep and have good patience then this coolant is for you, if you are impatient and just want to throw it into your loop then don’t buy.Overall I think it’s a great beautiful looking product if you are willing to go through the prep and think it’s worth it. I certainly doOn premochills website you can find all the information and warning about the fluid, they are very transparent with the difficulty of it and idk why people are bashing them saying they’ve been misled.Thanks for reading, hope this helps

The media could not be loaded. The PrimoChill Vue Pre-Mix (32oz) has been a fantastic addition to my computer’s water-cooling setup. First and foremost, the color is absolutely stunning—it adds an incredible visual appeal to the system that stands out beautifully. Beyond aesthetics, the cooling properties have been nothing short of impressive. It performs consistently and keeps my setup running smoothly, even under heavy loads.For anyone looking to combine style and performance in their water-cooling loop, the PrimoChill Vue Pre-Mix delivers on both fronts. Highly recommended!

Firstly I would like to say I correctly used the loop prep for the 72 hours and completely drained and dried my entire loop and components before installing and made sure all my fittings and components are nickel plated and copper. The fluid worked well for about 2 days and after leaving my PC on over night I woke up to the fluid looking transparent like it was just dyed water and my tubes looking crummy as if covered in finger prints. After a quick investigation every crack and corner in my blocks and my microfins are filled with the gunk of the "Vue visual indicator". While I will admit while it lasted it did indeed look amazing, this quick failure and annoyance of having to reclean my loop just to refill it with a different fluid will keep me from even considering trying this fluid again in the future.(UPDATE)after deep cleaning all my PC components including my pump and res and rads to my best ability, I put my system back together and refilled it. After about 5 minutes even more residue and debris had revealed itself and gotten back into my res and pump resulting in it running loud. After immediately turning my PC back off and redoing the whole process I take my pump apart to find that the bearing had grenaded itself. Really unfortunate that this is what happened considering I'm aware of the usual reliability this fluid has.

Followed the instructions and it's worth it. Looks so cool. Only down side is, the clean up is gonna be tedious every 6 months.

Looks Great at First... Then Becomes a NightmareI really wanted to love this coolant—the Sky White color is stunning right out of the bottle and gives your loop a unique, eye-catching look. But after just a couple of weeks, things started going downhill. The fluid began separating and left residue throughout my loop, clouding up the tubing and even clogging parts of the pump and CPU block. Flushing it out was a huge hassle, and I ended up having to do a full teardown. Great visual effect short-term, but not worth the long-term maintenance headache. Definitely not for long-term use.

I did a test run for 6 months, with a clean rad, used the primo prep, etc. I have a d5 non pwm pump by thermaltake, on medium setting. It lost its true color, left a very little bit of gunk.Its perfect for a show/asthetic build but not for a performance build. You will need to do a mentainence every 6 months or so.Overall if you are not going to keep everything in check and do maintenance its not for you.

Looks good. But not worth the cost nor having to be limited to pour on limits of 8hrs a day.I've had it in my system for a few months now and it still looks great! Not looking for ward to the teardown to clean it all out though.Will be going back to distilled with additives so I'm not limited to power on time. I built the system to be 24/7 but went for the wow factor on this fluid. Not sure how it would operate 24/7 but is not recommended by the manufacturer.Still looks good though.